1.1 This terminology consists of terms and definitions pertaining to the subject field of roofing and waterproofing, and in particular, terms related to standards generated by ASTM Committee D08 on Roofing and Waterproofing. 1.2 The purpose of this terminology is to provide preferred...
1.1 This terminology consists of terms and definitions pertaining to the subject field of roofing and waterproofing, and in particular, terms related to standards generated by ASTM Committee D08 on Roofing and Waterproofing. 1.2 The purpose of this terminology is to provide preferred...
This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims. The sheet shall be formulated from ethylene and higher...
5.1 The solar reflectance of a building envelope surface affects surface temperature and near-surface ambient air temperature. Surfaces with low solar reflectance absorb a high fraction of the incoming solar energy. Sunlight absorbed by a roof or by other building envelope surfaces can be conducted...
1.1 This guide covers the removal of test specimens from spray polyurethane foam (SPF) roofing systems in the field for the purpose of examination of an existing system and/or quality assurance for new installations. It describes the types and purposes of sample cuts, visual inspection...
1.1 This test method covers the determination of low-temperature flexibility of liquid-applied membranes used in roofing and waterproofing. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be...
1.1 These test methods cover determination of the breaking load of roofing slate and modulus of rupture of structural slate by use of simple three-point loading. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each...
This specification covers Grades G (granule surfaced) and S (smooth surfaced) prefabricated bituminous sheet materials reinforced with polyester fabric and modified by styrene butadiene styrene (SBS) thermoplastic elastomer, intended for use in the fabrication of multiple ply roofing and...
4.1 This guide is intended to provide building professionals with a comprehensive methodology for evaluating water leakage through walls. It addresses the performance expectations and service history of a wall, the various components of a wall, and the interaction between these components and...
4.1 This guide discusses various methods for evaluating the surface of structural concrete roof decks to receive adhered roofing system materials. 4.2 Methods for evaluating the surface of structural concrete roof decks to receive adhered roofing system materials included as part of a...
1.1 This test method covers the determination of parameters calculated from the measurement of modulus (G*) and phase angle (d) of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry in accordance with Test Method D7175. These parameters are considered important...
1.1 These test methods cover test procedures for prefabricated, reinforced, self-adhesive (SA) polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes. 1.2 These test methods specifically address the self-adhesive...
4.1 This field test method is suitable for determining the uplift resistance of the roofing system as stated in applicable specifications, bid documents, or where required by other authorities having jurisdiction. This field test method is also intended to supplement measurement of the...
4.1 Establishing standard practices and recommended procedures is a critical step required to achieve quality roofing and waterproofing system installations. This guide describes preparing typical substrates to receive hot-applied rubberized asphalt (HRA), melting and application of HRA,...
1.1 This guide provides guidance and considerations related to designing sustainable low-sloped roofing systems, including exposed membrane roofs, membranes covered with landscaped and vegetative (green) overburden systems, ballasted roofs, and protected membrane roofing assemblies. A...
This specification covers a liquid-applied solvent dispersed elastomeric coating used as a roofing membrane for spray polyurethane foam (SPF) insulation whose principal polymer in the dispersion contains more than 95 % silicone. The product, as manufactured, shall be in liquid form for...
Narrow Your Results