1.1 The purpose of this guide is to present methods and techniques for the visual inspection of electrical protective rubber products. This guide also includes descriptions and photographs of irregularities found in these products. Note 1: It is not the purpose of this guide to establish the...
1.1 This specification covers acceptance testing of rubber insulating matting for use as a floor covering for protection of workers. 1.2 Two types of matting, differing in chemical and physical characteristics, are provided and are designated as Type I and Type II matting. 1.3 The following...
1.1 These test methods cover tests for bondable silicone rubber tapes which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing). 1.2 These test methods appear in the following sections: ?????Test Method Section...
1.1 This specification covers acceptance testing of rubber insulating blankets for protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. 1.2 Two types of blankets are provided and are designated as Type I, not resistant to ozone, and Type II,...
This specification covers acceptance testing of rubber insulating covers for use as portable protective devices for protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. It includes insulator hoods, dead-end protectors, line hose connectors,...
1.1 This specification addresses the minimum performance for flexible laminate protective jacket and a pressure sensitive adhesive tape for use over thermal insulation on pipes, duct, and equipment operating at both above and below ambient temperatures and installed outdoors, above ground. It does...
1.1 This specification covers cored, annular, concentric-lay-stran
This specification covers aluminum 1350-H19, 1350-H16 or -H26, 1350-H14 or -H24, and 1350-H142 or -H242, bare concentric-lay-stran
These test methods cover the testing of heat-shrinkable tubing used for electrical insulation. Materials used include poly(vinyl chloride), polyolefins, fluorocarbon polymers, silicone rubber, and other plastic or elastomeric compounds. The values stated in inch-pound units are to be...
1.1 These test methods cover the testing of heat-shrinkable tubing used for electrical insulation. Materials used include poly(vinyl chloride), polyolefins, fluorocarbon polymers, silicone rubber, and other plastic or elastomeric compounds. 1.2 These test methods appear in the following...
This specification covers nonmetallic semi-conducting and electrically insulating rubber tapes designed for the splicing and repair of electrical wire and cables operating at specified phase to phase voltages. The tapes, which are classified into five types (Types I, II, III, IV, and V),...
These test methods cover the methods and procedures for testing electrically insulating and semi-conducting rubber tapes designed for splicing, terminating, and sheath repair of electrical wire and cable. The values stated in SI units are to be regarded as standard. The values given in...
1.1 These test methods cover the methods and procedures for testing electrically insulating and semi-conducting rubber tapes designed for splicing, terminating, and sheath repair of electrical wire and cable. 1.2 The test methods appear in the following sections: Section Referenced Documents...
1.1 This specification covers acceptance testing of rubber insulating blankets for protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. 1.2 Two types of blankets are provided and are designated as Type I, not resistant to ozone, and Type II,...
This specification covers nonmetallic semi-conducting and electrical insulating tapes designed for the splicing and repair of electrical wire and cables operating at voltages up to 325 kV, phase to phase. The SI values are the standard. The values stated in inch-pound units given in parentheses are...
This specification covers acceptance testing of rubber insulating blankets for protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. Two types of blankets are provided and are designated as Type I, not resistant to ozone, and Type II,...
This specification covers manufacturing and testing of rubber insulating sleeves for protection of workers from electrical shock. Two types of sleeves are provided and are designated as Type I, nonresistant to ozone, and Type II, resistant to ozone. Five classes of sleeves, differing in...
This Standard applies to the materials, construction, and testing of one- to four-conductor cross-linked polyethylene and ethylene propylene rubber-insulated shielded power cables, rated 5-46 kV, that are used for the distribution of electrical energy under normal conditions of installation...
The requirements of this Standard apply to materials, constructions, and testing of tree-retardant cross-linked polyethylene and ethylene propylene rubber-insulated single conductor or triplexed primary shielded and concentric neutral power cables rated 15 to 46 kV that are used for the...