loading
ASTM D4360-11(2026) - Standard Specification for Methyl n-Amyl Ketone
January 1, 2026 - ASTM International

1.1 This specification covers methyl n-amyl ketone (98?% grade) for use in paint, varnish, lacquer, and related products. 1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification. 1.3 The following applies to...

ASTM G101-04(2025) - Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
October 1, 2025 - ASTM International

1.1 This guide presents two methods for estimating the atmospheric corrosion resistance of low-alloy weathering steels, such as those described in Specifications A242/A242M, A588/A588M, A606/A606M Type 4, A709/A709M grades 50W, HPS 70W, and 100W, A852/A852M, and A871/A871M. One method gives...

ASTM D4528-88(2025) - Standard Classification for Rubber Compounding Materials—Sulfur
November 1, 2025 - ASTM International

1.1 This classification covers the variety of sulfur grades used in the rubber industry. Typical chemical and physical properties for sulfur are shown. Sulfur is principally used in unsaturated rubbers as a vulcanizing agent. 1.2 This international standard was developed in accordance with...

ASTM D6080-18a(2025) - Standard Practice for Defining the Viscosity Characteristics of Hydraulic Fluids
October 1, 2025 - ASTM International

1.1 This practice covers all hydraulic fluids based either on petroleum, synthetic, or naturally-occurring base stocks. It is not intended for water-containing hydraulic fluids. 1.2 For determination of viscosities at low temperature, this practice uses millipascal·second (mPa·s) as the unit of...

ASTM B678-25 - Standard Test Method for Solderability of Metallic-Coated Products
November 1, 2025 - ASTM International

4.1 In order that a sound solder joint be formed simply and quickly in a production operation, the molten solder must readily wet and spread over the surfaces of the products being joined. For this to happen, the surfaces must be clean or be soiled only with contaminants that are easily removed by...

ASTM A917-25 - Standard Specification for Steel Sheet, Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface (General Requirements)
October 1, 2025 - ASTM International

1.1 This specification covers hot-rolled and cold-rolled steel sheet coated by the electrolytic process. Coatings can be comprised of pure metals or metal alloys. For specific coatings, refer to Specifications A879/A879M and A918. 1.2 The product shall be coated on one or both surfaces with equal...

ASTM F3794-25 - Standard Practice for Multivariate Fit and Accommodation for Exoskeleton Manufacturers and Designers
November 1, 2025 - ASTM International

5.1 The U.S. exoskeleton marketplace currently lacks a consistent sizing structure and clear criteria for selecting sizes. This inconsistency likely stems from the absence of comprehensive national anthropometric data tailored to exoskeleton design applications. The significant variations in sizing...

ASTM D7917-25 - Standard Practice for Inductive Wear Debris Sensors in Gearbox and Drivetrain Applications
June 15, 2025 - ASTM International

5.1 This practice is intended for the application of online, full-flow, or bypass, or kidney loop sampling of wear debris via inductive sensors for gearbox and drivetrain applications. 5.2 Periodic sampling and analysis of lubricants have long been used as a means to determine overall machinery...

ASTM A765/A765M-24 - Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements
August 15, 2024 - ASTM International

1.1 This specification2 covers heat-treated carbon steel and alloy steel forgings with mandatory toughness requirements. These forgings are intended for pressure vessels, feedwater heaters, and similar uses. 1.2 These forgings include tube sheets, covers, channel barrels, integral forged channels,...

ASTM F2819-24 - Standard Test Methods for Measurement of Straightness of Bar, Rod, Tubing, and Wire to be Used for Medical Devices
August 15, 2024 - ASTM International

5.1 Significance-With the birth of minimally invasive surgery in the 1960s, there has been a requirement for guide wires. The guide wires serve as the access line by which procedures like balloon angioplasty and stent placement are conducted. A guide wire typically consists of a mandrel, coil, and...

ASTM F3148-17a(2024) - Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions
June 1, 2024 - ASTM International

This specification defines chemical, dimensional, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch dimensions. Structural bolting assemblies are designated as Grade 144. Bolts are designated by type denoting raw material...

ASTM D1765-23b - Standard Classification System for Carbon Blacks Used in Rubber Products
December 15, 2023 - ASTM International

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The...

ASTM F519-23 - Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
December 1, 2023 - ASTM International

1.1 This test method describes mechanical test methods and defines acceptance criteria for coating and plating processes that can cause hydrogen embrittlement in steels. Subsequent exposure to chemicals encountered in service environments, such as fluids, cleaning treatments or maintenance...

ASTM B678-23 - Standard Test Method for Solderability of Metallic-Coated Products
November 1, 2023 - ASTM International

4.1 In order that a sound solder joint be formed simply and quickly in a production operation, the molten solder must readily wet and spread over the surfaces of the products being joined. For this to happen, the surfaces must be clean or be soiled only with contaminants that are easily removed by...

ASTM D1765-23a - Standard Classification System for Carbon Blacks Used in Rubber Products
April 1, 2023 - ASTM International

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The...

ASTM F1609-23 - Standard Specification for Calcium Phosphate Coatings for Implantable Materials
July 1, 2023 - ASTM International

1.1 This specification covers the material requirements for calcium phosphate coatings for surgical implant applications. 1.2 In particulate and monolithic form, the calcium phosphate materials system has been well characterized regarding biological response (1, 2)2 and laboratory characterization...

ASTM D1765-23 - Standard Classification System for Carbon Blacks Used in Rubber Products
February 1, 2023 - ASTM International

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The...

ASTM D1765-22 - Standard Classification System for Carbon Blacks Used in Rubber Products
December 1, 2022 - ASTM International

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The...

ASTM A765/A765M-07(2022) - Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements
September 1, 2022 - ASTM International

1.1 This specification2 covers heat-treated carbon steel and alloy steel forgings with mandatory toughness requirements. These forgings are intended for pressure vessels, feedwater heaters, and similar uses. 1.2 These forgings include tube sheets, covers, channel barrels, integral forged channels,...

ASTM D6874-22a - Standard Test Methods for Nondestructive Evaluation of the Stiffness of Wood and Wood-Based Materials Using Transverse Vibration or Stress Wave Propagation
October 1, 2022 - ASTM International

1.1 These test methods cover the non-destructive determination of the following dynamic properties of wood and wood-based materials from measuring the fundamental frequency of vibration: 1.1.1 Flexural (see Refs (1-3))2 stiffness and apparent modulus of elasticity (Etv) properties using simply or...

Advertisement