loading
ASTM E2132-25 - Standard Practice for Inventory Verification: Electronic and Physical Inventory of Assets
December 1, 2025 - ASTM International

4.1 Inventory verification is conducted to accomplish one or more of the following: 4.1.1 Assess the accuracy of asset records, 4.1.2 Validate or update asset records, or both, 4.1.3 Assess asset loss experience, 4.1.4 Identify process inconsistencies, and 4.1.5 Provide the status of the verified...

ISO LIST SERIAL ABBREV - LIST OF SERIAL TITLE WORD ABBREVIATIONS
ISO
A description is not available for this item.
ASTM E1878-97(2025) - Standard Specification for Laboratory Glass Volumetric Flasks, Special Use
July 1, 2025 - ASTM International

1.1 This specification covers requirements for glass volumetric flasks of precision grades suitable for laboratory purposes and of specialty use. Each flask shall be marked with the letter "A" to signify compliance with applicable construction and accuracy requirements. Flasks may be marked with an...

ASTM B951-11(2025) - Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought
May 1, 2025 - ASTM International

This practice provides a system for the codification of unalloyed magnesium and magnesium alloys in the cast and wrought forms. Code designations shall be based on their chemical composition limits. For alloys, designations shall consist of not more than two letters representing the alloying...

ASTM F3716-25 - Standard Test Method for Cumulative Population Doubling Analysis of the Proliferation of Vertebrate Tissue Cell Preparations
February 15, 2025 - ASTM International

5.1 Background for CPD Analyses for in vitro Vertebrate Tissue Cell Proliferation Studies-Since Leonard Hayflick's early reports on in vitro tissue cell culture studies in the 1960s, CPD data derived from serial cell culture have been used in in vitro tissue cell research as a basis for...

ASTM E288-10(2025) - Standard Specification for Laboratory Glass Volumetric Flasks
July 1, 2025 - ASTM International

1.1 This specification covers requirements for glass volumetric flasks of precision and general-purpose grades suitable for laboratory purposes. 1.1.1 Class A-Each flask of precision grade shall be marked with the letter "A" to signify compliance with applicable construction and accuracy...

ASTM F983-24 - Standard Practice for Permanent Marking of Orthopaedic Implant Components
December 1, 2024 - ASTM International

This practice covers recommendations on permanent marking of metallic and nonmetallic orthopaedic implant components. The practical amounts of information that should be included in the marking are specified. Where implant size and shape allow, it is recommended that the following standard...

ASTM E287-02(2024) - Standard Specification for Laboratory Glass Graduated Burets
November 1, 2024 - ASTM International

1.1 This specification covers requirements for glass burets of precision and general-purpose grades suitable for laboratory use. 1.1.1 Class A-Each buret of precision grade may be marked with the letter "A" to signify compliance with applicable construction and accuracy requirements in Table 1 and...

ASTM E1272-02(2024) - Standard Specification for Laboratory Glass Graduated Cylinders
November 1, 2024 - ASTM International

1.1 This specification covers requirements for glass graduated cylinders for precision and general purpose grades suitable for laboratory purposes. 1.1.1 Class A-Each cylinder of precision grade shall be marked with the letter "A" to signify compliance with applicable construction and accuracy...

ASTM F2268-03(2023) - Standard Specification for Bicycle Serial Numbers
November 1, 2023 - ASTM International

1.1 This standard specifies the format, content, number of characters and physical requirements for serial numbers to facilitate recall campaigns and identification of stolen property. 1.2 This standard is applicable to all bicycles, refer to Classification F2043 on definition for bicycle. 1...

ASTM E694-18(2024) - Standard Specification for Laboratory Glass Volumetric Apparatus
February 1, 2024 - ASTM International

1.1 This specification covers general requirements common to glass volumetric apparatus. Specific dimensions and tolerances for applicable instruments are given in other specifications as cited throughout this specification. Glass must conform to Specifications E438 and be calibrated in accordance...

J2497_202311 - Power Line Carrier Communications for Commercial Vehicles
November 1, 2023 - SAE International

This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and...

ASTM F3327-23 - Standard Practice for Recording the A-UGV Test Configuration
December 1, 2023 - ASTM International

5.1 The significance of the information to be recorded in a test report allows for A-UGV performance to be contextualized with A-UGV configuration. 5.2 Limitations of the practice are that not all A-UGVs have the same capabilities or configuration parameters. For example, for capabilities, a...

ASTM E1402-13(2023) - Standard Guide for Sampling Design
November 1, 2023 - ASTM International

4.1 This guide describes the principal types of sampling designs and provides formulas for estimating population means and standard errors of the estimates. Practice E105 provides principles for designing probability sampling plans in relation to the objectives of study, costs, and practical...

USCAR30-1 - PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM
July 10, 2023 - SAE International

Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of any USB cable assemblies and associated connections that constitute the electrical connection systems between the consumer peripheral interface and...

J1939_202306 - Serial Control and Communications Heavy-Duty Vehicle Network - Top-Level Document
June 2, 2023 - SAE International

This top-level document provides a general overview of the SAE J1939 network and describes the subordinate document structure. This document includes definitions of terms and abbreviations which are used among the various SAE J1939 subordinate documents.

ASTM F3637-23 - Standard Guide for Additive Manufacturing of Metal — Finished Part Properties — Methods for Relative Density Measurement
May 15, 2023 - ASTM International

5.1 General: 5.1.1 This guide is intended to support PBF-LB process and parameter development, part acceptance criteria, and process control tests. 5.1.2 Flaws and Defects-Fabricating fully dense parts continues to be a challenge in AM as the process intrinsically introduces volumetric flaws into a...

ASTM E1245-03(2023) - Standard Practice for Determining the Inclusion or Second-Phase Constituent Content of Metals by Automatic Image Analysis
April 1, 2023 - ASTM International

5.1 This practice is used to assess the indigenous inclusions or second-phase constituents of metals using basic stereological procedures performed by automatic image analyzers. 5.2 This practice is not suitable for assessing the exogenous inclusions in steels and other metals. Because of the...

USCAR30 - PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM
July 4, 2022 - SAE International

Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of any USB cable assemblies and associated connections that constitute the electrical connection systems between the consumer peripheral interface and...

Advertisement