The Manual of Guidelines for Shop Safety is a comprehensive pocket-sized (4" x 6") publication which includes a variety of shop safety aspects and guidlines. Includes information on the use of shop equipment including crane safety. Product code: 30-SSM
1.1 This standard covers performance requirements, test methods, and marking/labeling requirements for special needs shopping carts. 1.2 This standard is intended to address special needs shopping carts for use by children and adults with special needs. 1.3 This standard does not...
1.1 This specification covers the required release and retention characteristics of ski-binding-boot (S-B-B) systems. This specification is applicable to all recreational snow skiing bindings that have safety release mechanisms. Specifically, this performance standard establishes the minimum...
1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants...
1.1 This test method describes the apparatus and procedure for evaluating the pull-off strength of wet lay-up or pultruded (shop-fabricated) Fiber Reinforced Polymer (FRP) laminate systems adhesively bonded to a flat concrete substrate. The test determines the greatest perpendicular force...
1.1 This practice provides tables of dimensions of preformed pipe insulation that shall be used in fabricating insulation covers for use on valves, ells, tees, flanges, and vessels in the pressure range from 150 to 1500 psi (1 to 10 MPa). These tables, which are part of this standard, are published...
1.1 The purpose of this practice is to delineate requirements regarding the design, manufacture, installation, operation, maintenance, inspection and major modification of commercial or institutional trampoline courts designed for amusement, entertainment or recreation. 1.2 This standard applies to...
4.1 Abrasive media may contain ionic contamination naturally (for example, mineral abrasives), from manufacturing (quenching with contaminated water), transportation, storage or use (in the case of abrasive that is reused). Ionic contamination on the abrasive may transfer to the surface during...
4.1 Wet film thickness measurements of coatings applied on articles can be very helpful in controlling the thickness of the final dry coating, although in some specifications the wet film thickness is specified. Most protective and high performance coatings are applied to meet a requirement or...
1.1 This practice is used to determine the presence of oil in abrasives used for abrasive blast cleaning. 1.2 The procedure can be used in the laboratory, field, blast and paint shop or steel fabrication shop. 1.3 The values stated in SI units are to be regarded as the standard. The...
1.1 This specification covers standardizing the dimensions and materials for the manufacture of 25/8-in.?and 4-in. diameter steel or cast iron shear plates used in the fabrication of connections in wood constructions. The referencing of this specification in design, construction, and purchase order...
This specification covers the requirements for extruded (cast or blown) and compression-molded sheeting made from low-, medium-, and high-density polyethylenes and copolymers in specified thicknesses. Depending on the functional requirements, sheeting conforming to this specification is used in...
5.1 Solvent cement bonder/installers shall follow all procedures to produce consistently strong and leak-free joints, either in shop operations or in the field.
4.1 This test method provides a means of verifying that masonry materials used in construction result in masonry that meets the specified compressive strength (Note 1). Note 1: A prism is an assembly of components used to measure (in this case, the tested compressive strength of masonry, f mt) or...
5.1 A solvent cement bonder/installer must follow all procedures to produce consistently strong and leak-free joints, either in shop operations or in the field.
This specification covers the material and dimensional requirements applicable to lap joint flange pipe ends that are manufactured by a mechanical forming process, and are widely used for low-pressure systems in the marine, process piping, and similar industries. Materials having acceptable forming...
These practices are intended for production and preparation of gray iron castings for porcelain enamelling. Design of the casting should be such as to minimize variations in temperature during firing and cooling. The governing factors in pattern layout and shop control are elimination of...
1.1 This specification covers the required release and retention characteristics of ski-binding-boot (S-B-B) systems. This specification is applicable to all recreational snow skiing bindings that have safety release mechanisms. Specifically, this performance standard establishes the minimum...
5.1 The techniques described herein are used to produce leak-tight press-connect joints between copper and copper alloy tube and fittings either in shop operations or the field. Operator or mechanic's skill and knowledge is required to obtain a satisfactory joint. 5.1.1 Refer to...
1.1 This practice describes a solvent rub technique for assessing the MEK resistance of ethyl silicate (inorganic) zinc-rich primers. The MEK resistance of some two-component ethyl silicate zinc-rich primers has been shown to correlate well with the cure of the primer as determined by diffuse...
Narrow Your Results