4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled...
1.1 This test method covers the determination of the density of solid plastics. 1.2 This test method is based on observing the level to which a test specimen sinks in a liquid column exhibiting a density gradient, in comparison with standards of known density. Note 1: This test method is...
1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
This specification covers round, square, rectangular, and special shape electric-resistance-
5.1 VOCs emitted from materials/products affect indoor air quality (IAQ) in buildings. To determine the impact of these emissions on IAQ, it is necessary to know their emission rates over time. This practice provides guidelines for using a full-scale environmental chamber for testing large...
5.1 These test methods are intended to evaluate the ability of the grease duct enclosure system to do the following: 5.1.1 Resist the effects of a standardized fire exposure, 5.1.2 Retain its integrity, or 5.1.3 Exhibit both properties dependent upon the type of test assembly involved during a...
5.1 The purpose of this test method is to measure the net heat flux to or from a surface location. For measurement of the radiant energy component the emissivity or absorptivity of the surface coating of the gage is required. When measuring the convective energy component, the potential physical...
3.1 This test method is intended specifically for testing the porcelain enamel finish on stoves, table tops, sinks, and other sanitary ware, laundry appliances, architectural units, etc., where the surface may come in contact with food acids at room temperature. 3.2 Citric acid has been...
5.1 Indoor materials/products are products or materials used for construction works or in the indoor environment. The area specific emission rates of volatile organic compounds from an indoor material/product may be used to estimate the expected contribution of emissions from that material/product...
5.1 These test methods are intended to evaluate the ability of the HVAC duct system and its supporting construction to do the following: 5.1.1 Resist the effects of a standardized fire exposure, and 5.1.2 Retain its integrity. 5.2 These test methods provide for the following measurements and...
This specification covers round, square, rectangular, and special shape electric-resistance-
This specification covers single- and double compression and self-closing faucets for shipboard plumbing installations. Faucets may be classified into nine types: Type I is the standard (bibb) with three classes namely Class A (compression, plain end), Class B (compression, hose end), and Class C...
4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled...
This test method covers the determination of the efficiency of ordinary commercial wetting agents using the skein test. It is applicable under limited and controlled conditions, but does not necessarily yield information correlating with specific end uses. The apparatus is comprised of a hook of...
1.1 This test method covers the determination of the percentage of lightweight particles in aggregate by means of sink-float separation in a heavy liquid of suitable specific gravity. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The...
4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled...
1.1 This specification covers material, design, structural performance, and manufacturing practice requirements for monolithic or sectional corrugated polyethylene grease interceptor tanks with volumes equal to or greater than 333 gal (1260 L). 1.2 The corrugated high density polyethylene (HDPE)...
1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI...
1.1 This test method covers the analysis of cast iron by spark atomic emission spectrometry for the following elements in the ranges shown (Note 1): Ranges, % Elements Applicable Range, % Quantitative Range, %A Carbon 1.9 to 3.8 1.90? to 3.8 Chromium 0 to 2.0 0.025 to 2.0 Copper 0 to 0.75 0.015 to...
6.1 Contaminated sediments may affect natural populations of aquatic organisms adversely. Sediment-dwelling organisms may be exposed directly to contaminants by the ingestion of sediments and by the uptake of sediment-associated contaminants from interstitial and overlying water. Contaminated...
Narrow Your Results