loading
ASTM F2138-12(2024) - Standard Specification for Excess Flow Valves for Natural Gas Service
July 1, 2024 - ASTM International

This specification covers requirements and test methods for excess flow valves for natural gas piping systems. Tests methods requirements shall determine the performance characteristics of an excess flow valve installed in a straight piece of pipe. Excess flow valves shall conform to specified...

ASTM D2050-23 - Standard Terminology Relating to Fastener Subassemblies Used in the Manufacture of Textiles
June 1, 2023 - ASTM International

1.1 This standard identifies terminology related to subassemblies which are categorized as any component that is used in the construction or assembly of a textile product. Subassemblies can be in the form of components used as closures (for example, slide fasteners, buttons, snap fasteners,...

ASTM A861-04(2023) - Standard Specification for High-Silicon Iron Pipe and Fittings
May 1, 2023 - ASTM International

This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction. The castings shall be true to pattern, reasonable smooth, and free from defects that would make the castings unfit for the use for which they are...

ASTM F963-23 - Standard Consumer Safety Specification for Toy Safety
August 1, 2023 - ASTM International

1.1 This specification2 relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a toy is intended or after reasonably foreseeable abuse. It does not purport to cover every conceivable hazard of a particular toy. This...

ASTM D4846-96(2021) - Standard Test Method for Resistance to Unsnapping of Snap Fasteners
July 1, 2021 - ASTM International

1.1 This test method covers the determination of the force required to disengage snap fasteners by a pull perpendicular to and parallel with the plane of the snap fastener. 1.2 This test method requires attachment of snaps to specimens using specifications provided by the...

ASTM D7142-05(2021) - Standard Test Method for Holding Strength of Prong-Ring Attached Snap Fasteners
July 1, 2021 - ASTM International

5.1 Both test methods are considered satisfactory for acceptance testing of commercial shipments of garments with prong-ring type snap fasteners. 5.1.1 In case of dispute arising from differences in reported test results when using this test method for acceptance of commercial shipment, the...

NASM27986 - FASTENERS, SNAP, STYLE 7, RIVET TYPE
December 30, 2020 - AIA/NAS
A description is not available for this item.
NASM43770/7 - SNAP HOOKS, CAST BODY, LOOP EYE SWIVEL
November 30, 2020 - AIA/NAS
A description is not available for this item.
NASM43770 - SNAP HOOKS, GENERAL SPECIFICATION FOR
March 29, 2019 - AIA/NAS

This specification covers the general requirements for snap hooks. Specific requirements for snap hooks are covered by the applicable part standards (see 6.3).

JIS B 1509 - Rolling bearings — Radial bearings with locating snap ring — Dimensions, geometrical product specifications (GPS) and tolerance values
March 23, 2020 - JSA

This Standard specifies the snap ring groove dimensions and tolerance values, chamfer dimensions on the snap ring groove side of the outer ring, and the dimensions of locating snap ring (hereafter referred to as snap rings) and tolerance values for radial bearings in the...

ISO 18885-3 - TPMS snap-in valves — Part 3: Performances
September 1, 2019 - ISO

This document specifies test methods for TPMS snap-in tubeless valves. These methods are defined to determine the minimum level of performances requested.

NAS1051 - SAFETY HOOK, FORGED CARBON STEEL, SNAP, DIRECT EYE (FOR GROUND SUPPORT EQUIPMENT)
January 29, 2021 - AIA/NAS
A description is not available for this item.
NASM43770/12 - SNAP HOOKS, CAST BODY, FIXED ROUND EYE W/O ROLLER, FLAT SPRING CLOSURE
November 30, 2020 - AIA/NAS
A description is not available for this item.
DIN 9926 - Round wire snap rings for bores
December 1, 2019 - DIN
A description is not available for this item.
DIN 9925 - Round wire snap rings for shafts
December 1, 2019 - DIN
A description is not available for this item.
QPL-15291 - Switches, Rotary, Snap Action and Detent/Spring Return Action, General Specification for
November 15, 2019 - NPFC

QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION MIL-DTL-15291 Switches, Rotary, Snap Action and Detent/Spring Return Action, General Specification for This list has been prepared for use by or for the Government in the acquisition of products covered by the...

QPL-8805 - Switches and Switch Assemblies, Sensitive, Snap Action (Basic, Limit, Push Button and Toggle Switches), General Specification for
December 11, 2019 - NPFC

QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION MIL-PRF-8805 Switches and Switch Assemblies, Sensitive, Snap Action (Basic, Limit, Push Button and Toggle Switches), General Specification for This list has been prepared for use by or for the Government in the...

Advertisement