loading
GME 12584 PART 1 - Temperature Sensor
January 1, 2013 - GME

This specification defines the general peformence requirements for sensor for measering of temperatures.

ARP5623A - Mobile Digital Infrared Pavement Surface, Ambient Air and Dew Point Temperature Sensor System
February 20, 2023 - SAE International

This SAE Aerospace Recommended Practice (ARP) covers the requirements for a combined Mobile Digital Infrared Pavement Surface, Ambient Air, and Dew Point Temperature Sensing System (referred to as the system). The system monitors real-time surface, air and dew point temperatures of...

ASTM D7962-21 - Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
May 1, 2021 - ASTM International

1.1 This practice describes two procedures for use with temperature measurement devices. Methodology is described for determining minimum immersion depth for thermal sensors, in particular RTDs or similar temperature sensors. Included is a procedure for consistently...

SMD 5962-17218 - MICROCIRCUIT, DIGITAL-LINEAR, TEMPERATURE SENSOR, MONOLITHIC SILICON
July 10, 2018 - DOD

This drawing documents two product assurance class levels consisting of high reliability (device class Q) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of...

GME 12584-2 - Temperature Sensor Part 2: Sensor-Outside Air
May 1, 2015 - GME

This specification defines the general performance requirements for sensor for measuring of temperatures and indication of the outer air temperature used on passenger cars.

ASTM D6176-97(2022) - Standard Practice for Measuring Surface Atmospheric Temperature with Electrical Resistance Temperature Sensors
March 1, 2022 - ASTM International

1.1 This practice provides procedures to measure representative near-surface atmospheric (outdoor air) temperature for meteorological purposes using commonly available electrical thermometers housed in radiation shields mounted on stationary or portable masts or towers. 1.2 This practice is...

ASTM E1040-10(2026) - Standard Specification for Physical Characteristics of Nonconcentrator Terrestrial Photovoltaic Reference Cells
June 1, 2026 - ASTM International

This specification describes the physical requirements for primary and secondary nonconcentrator terrestrial phorovoltaic reference cells based on small-cell package design and module-package design. These requirements include those for product marking, reference cell material, window,...

ASTM E3137/E3137M-26 - Standard Specification for Heat Meter Instrumentation
March 1, 2026 - ASTM International

This specification applies to heat meters used to measure heat in heat exchange circuits in which energy is absorbed (cooling) or given up (heating) by a flowing liquid. For this specification, the necessary elements of a heat meter consist of a sensor to measure flow of the heat-conveying...

MIL-T-49447 - TEMPERATURE SENSOR, RESISTANCE
NPFC
A description is not available for this item.
ISO TR 27957 - Road vehicles — Temperature measurement in anthropomorphic test devices — Definition of the temperature sensor locations
April 1, 2020 - ISO

This document defines the number and the arrangement of temperature measuring points for anthropomorphic test devices in order to ensure that the temperature of the ATD is in accordance with the temperature corridor prescribed by the applied test procedure.

IEC 62765-2 - Nuclear powers plants - Instrumentation and control important to safety - Management of ageing of sensors and transmitters - Part 2: Temperature sensors
January 1, 2019 - IEC

This part of IEC 62765 identifies minimum requirements and applicable practices for correcting and preventing any potential impacts on nuclear power plant (NPP) safety due to the ageing of temperature sensors, such as NPP resistance temperature detectors (RTDs) and...

SMD 5962-96687 - MICROCIRCUIT, LINEAR, PRECISION TEMPERATURE SENSOR, MONOLITHIC SILICON
November 1, 2012 - DOD

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are...

ASTM D7962-16 - Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
December 1, 2016 - ASTM International

1.1 This practice describes a two procedures for use with temperature measurement devices. Methodology is described for determining minimum immersion depth for thermal sensors, in particular RTDs or similar temperature sensors. Included is a procedure for consistently...

GMW16839 - Discharge (DAT), Evaporator (EAT) and CHAT (Condensing Heater) Air Temperature Sensors
July 1, 2020 - GMW
A description is not available for this item.
ASTM D7962 - Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
May 1, 2017 - ASTM

This practice describes two procedures for use with temperature measurement devices. Methodology is described for determining minimum immersion depth for thermal sensors, in particular RTDs or similar temperature sensors. Included is a procedure for consistently...

ASTM D7962-17 - Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
May 1, 2017 - ASTM International

1.1 This practice describes two procedures for use with temperature measurement devices. Methodology is described for determining minimum immersion depth for thermal sensors, in particular RTDs or similar temperature sensors. Included is a procedure for consistently...

ASTM E1953-26 - Standard Practice for Description of Thermal Analysis and Rheology Apparatus
March 1, 2026 - ASTM International

4.1 Section 5 identifies essential instrumentation and accessories required to perform thermal analysis, rheometry, or viscometry for a variety of different instruments. The appropriate generic instrument description should be included in any test method describing use or application of the thermal...

ASTM ASTM51631-26 - Standard Practice for Use of Calorimetric Dosimetry Systems for Dose Measurements and Routine Dosimetry System Calibration in Electron Beams
May 1, 2026 - ASTM International

1.1 This practice covers the preparation and use of semi-adiabatic calorimetric dosimetry systems for measurement of absorbed dose and for calibration of routine dosimetry systems when irradiated with electrons for radiation processing applications. The calorimeters are either transported by a...

Advertisement