5.1 This equipment may be used to bring about the changes in texture on the surface of pile floor covering caused by mechanical action. 5.2 The acceptance criteria of this practice shall be set by mutual agreement between the purchaser and the supplier.
4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...
1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under certain...
1.1 This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. Three types of thin veneer brick units in each of two grades are covered. In this specification, the...
1.1 This specification covers the requirements for interlocking concrete pavers manufactured for the construction of paved surfaces. 1.2 Concrete units covered by this specification shall be made with lightweight or normal weight aggregates or both. Note 1: If particular features are desired, such...
1.1 This specification covers the requirements for segmental concrete paving slabs used for construction of pedestal-set applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-presse
This specification covers resilient floor covering having a vinyl plastic wear layer with backing intended for use in commercial, light commercial, and residential building applications. Material covered by this specification consists of Types I and II floor covering, which may further be...
1.1 This specification covers the requirements for segmental concrete paving slabs manufactured for construction of pedestrian and roof applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-presse
1.1 This specification covers brick intended for use in masonry supplying structural or facing components, or both, to the structure. 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining...
1.1 This test method covers a procedure to measure the thickness of smooth geomembranes and core thickness of textured geomembranes. 1.2 This test method does not provide thickness values for geomembranes under variable normal stresses. 1.3 The values stated in either SI units or inch-pound...
5.1 This practice is intended for the collection of settled dust samples for the subsequent measurement of beryllium and compounds. The practice is meant for use in the collection of settled dust samples that are of interest in clearance, hazard evaluation, risk assessment, and other purposes. 5.2...
1.1 This practice covers a short-term testing method to screen the subcutaneous tissue reaction to implant candidate materials in small laboratory animals. The material may be dense or porous. This method may not work for absorbable materials, depending on the absorption kinetics. The tissue...
1.1 This specification covers either untextured or surface textured fiber-cement flat sheets intended for exterior applications such as wall claddings, facades, curtain walls, soffits, trim, and so forth. 1.2 This specification is not applicable to asbestos-cement flat sheets (Specification...
These test methods cover the standard procedures and related calculations for determining the saturated hydraulic conductivity, water retention, porosity, and bulk density of sand-based root zone mixtures used in the construction and topdressing of golf course putting greens including United States...
5.1 This practice is intended for the collection of samples on surfaces for the subsequent measurement of target nonvolatile and semi-volatile organic chemicals. The practice is meant for use in the collection of samples that are of interest in hazard evaluation, exposure assessment, risk...
1.1 This speci?cation describes the production of welded copper and copper alloy tubes with a longitudinal seam free of ?ller metal produced from sheet or strip up to 1.5 in. (38.1?mm), in diameter for use in surface condensers, evaporators, heat exchangers, and general engineering applications....
1.1 This test method specifies the test requirements for (FRP) composite smooth round rods and textured bars for determining the transverse shear strength via a double shear fixture. FRP rods and bars are often loaded in transverse shear when these elements are used as dowels in concrete...
1.1 This specification covers brick intended for use in masonry supplying structural or facing components, or both, to the structure. 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining...
4.1 These practices should be used only to collect visible samples that are suspected biological agents and toxins and have been field screened as defined by the FBI-DHS-HHS/CDC Coordinated Document for explosive hazard, radiological hazard, and other acute chemical hazards. 4.2 These practices...
1.1 This specification covers PB Exterior Insulation and Finish Systems (EIFS) defined as an exterior, non-bearing wall covering providing a weather-resistant exterior wall envelope on walls required to be combustible or noncombustible, fire-resistance-rate
Narrow Your Results