loading
ASTM D5417-21(2026) - Standard Practice for Operation of the Vettermann Drum Tester
July 1, 2026 - ASTM International

5.1 This equipment may be used to bring about the changes in texture on the surface of pile floor covering caused by mechanical action. 5.2 The acceptance criteria of this practice shall be set by mutual agreement between the purchaser and the supplier.

ASTM D6752/D6752M-26 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
August 1, 2026 - ASTM International

4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...

ASTM C129-26 - Standard Specification for Dry-Cast Nonloadbearing Concrete Masonry Units
July 15, 2026 - ASTM International

1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under certain...

ASTM C1088-26 - Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
June 1, 2026 - ASTM International

1.1 This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. Three types of thin veneer brick units in each of two grades are covered. In this specification, the...

ASTM C936/C936M-26 - Standard Specification for Solid Concrete Interlocking Paving Units
June 1, 2026 - ASTM International

1.1 This specification covers the requirements for interlocking concrete pavers manufactured for the construction of paved surfaces. 1.2 Concrete units covered by this specification shall be made with lightweight or normal weight aggregates or both. Note 1: If particular features are desired, such...

ASTM C1944/C1944M-26 - Standard Specification for Pedestal-Set Concrete Paving Slabs
June 1, 2026 - ASTM International

1.1 This specification covers the requirements for segmental concrete paving slabs used for construction of pedestal-set applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-pressed process or some combination of these...

ASTM F1303-26 - Standard Specification for Sheet Vinyl Floor Covering with Backing
June 1, 2026 - ASTM International

This specification covers resilient floor covering having a vinyl plastic wear layer with backing intended for use in commercial, light commercial, and residential building applications. Material covered by this specification consists of Types I and II floor covering, which may further be...

ASTM C1782/C1782M-26 - Standard Specification for Segmental Concrete Paving Slabs
June 1, 2026 - ASTM International

1.1 This specification covers the requirements for segmental concrete paving slabs manufactured for construction of pedestrian and roof applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-pressed process or some combination...

ASTM C216-26a - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
June 1, 2026 - ASTM International

1.1 This specification covers brick intended for use in masonry supplying structural or facing components, or both, to the structure. 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining...

ASTM D5994/D5994M-26 - Standard Test Method for Measuring the Thickness of Geomembranes
April 1, 2026 - ASTM International

1.1 This test method covers a procedure to measure the thickness of smooth geomembranes and core thickness of textured geomembranes. 1.2 This test method does not provide thickness values for geomembranes under variable normal stresses. 1.3 The values stated in either SI units or inch-pound...

ASTM D7296-26 - Standard Practice for Collection of Settled Dust Samples Using Dry Wipe Sampling Methods for Subsequent Determination of Beryllium and Compounds
April 1, 2026 - ASTM International

5.1 This practice is intended for the collection of settled dust samples for the subsequent measurement of beryllium and compounds. The practice is meant for use in the collection of settled dust samples that are of interest in clearance, hazard evaluation, risk assessment, and other purposes. 5.2...

ASTM F1408-20a(2026) - Standard Practice for Subcutaneous Screening Test for Implant Materials
April 15, 2026 - ASTM International

1.1 This practice covers a short-term testing method to screen the subcutaneous tissue reaction to implant candidate materials in small laboratory animals. The material may be dense or porous. This method may not work for absorbable materials, depending on the absorption kinetics. The tissue...

ASTM C1186-26 - Standard Specification for Flat Fiber-Cement Sheets
April 1, 2026 - ASTM International

1.1 This specification covers either untextured or surface textured fiber-cement flat sheets intended for exterior applications such as wall claddings, facades, curtain walls, soffits, trim, and so forth. 1.2 This specification is not applicable to asbestos-cement flat sheets (Specification...

ASTM F1815-11(2026) - Standard Test Methods for Saturated Hydraulic Conductivity, Water Retention, Porosity, and Bulk Density of Athletic Field Rootzones
March 1, 2026 - ASTM International

These test methods cover the standard procedures and related calculations for determining the saturated hydraulic conductivity, water retention, porosity, and bulk density of sand-based root zone mixtures used in the construction and topdressing of golf course putting greens including United States...

ASTM D8569-26 - Standard Practice for Surface Sampling of Non-Volatile and Semi-Volatile Organic Chemicals for Worker Protection
January 1, 2026 - ASTM International

5.1 This practice is intended for the collection of samples on surfaces for the subsequent measurement of target nonvolatile and semi-volatile organic chemicals. The practice is meant for use in the collection of samples that are of interest in hazard evaluation, exposure assessment, risk...

ASTM B1014-20(2026) - Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s)
January 1, 2026 - ASTM International

1.1 This speci?cation describes the production of welded copper and copper alloy tubes with a longitudinal seam free of ?ller metal produced from sheet or strip up to 1.5 in. (38.1?mm), in diameter for use in surface condensers, evaporators, heat exchangers, and general engineering applications....

ASTM D7617/D7617M-25 - Standard Test Method for Transverse Shear Strength of Fiber-Reinforced Polymer Matrix Composite Bars
December 15, 2025 - ASTM International

1.1 This test method specifies the test requirements for (FRP) composite smooth round rods and textured bars for determining the transverse shear strength via a double shear fixture. FRP rods and bars are often loaded in transverse shear when these elements are used as dowels in concrete...

ASTM C216-26 - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
February 1, 2026 - ASTM International

1.1 This specification covers brick intended for use in masonry supplying structural or facing components, or both, to the structure. 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining...

ASTM E2458-26 - Standard Practices for Bulk Sample Collection and Swab Sample Collection of Visible Powders Suspected of Being Biological Agents and Toxins from Nonporous Surfaces
January 15, 2026 - ASTM International

4.1 These practices should be used only to collect visible samples that are suspected biological agents and toxins and have been field screened as defined by the FBI-DHS-HHS/CDC Coordinated Document for explosive hazard, radiological hazard, and other acute chemical hazards. 4.2 These practices...

ASTM E2568-17a(2026) - Standard Specification for PB Exterior Insulation and Finish Systems
January 1, 2026 - ASTM International

1.1 This specification covers PB Exterior Insulation and Finish Systems (EIFS) defined as an exterior, non-bearing wall covering providing a weather-resistant exterior wall envelope on walls required to be combustible or noncombustible, fire-resistance-rated or nonfire-resistance-rated. Further, PB...

Advertisement