loading
ASTM E376-26 - Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy Current (Electromagnetic) Testing Methods
July 1, 2026 - ASTM International

4.1 General-Most thickness gauges are not applicable to all combinations of coating-substrate thicknesses and materials. The limitations of a particular instrument are generally delineated by its manufacturer. The substrate material and coating combination to be measured as well as...

ASTM D7241-22(2026) - Standard Test Method for Pile Thickness of Finished Multilevel Pile Yarn Floor Covering
July 1, 2026 - ASTM International

1.1 This test method covers the determination of pile thickness of finished multilevel pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the...

ASTM E446-20(2026) - Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
July 1, 2026 - ASTM International

1.1 These reference radiographs illustrate various categories, types, and severity levels of discontinuities occurring in steel castings that have section thicknesses up to 2 in. (50.8 mm) (see Note 2). The reference radiograph films are an adjunct to this standard and must be purchased...

ASTM E802-21(2026) - Standard Reference Radiographs for Gray Iron Castings Up to 4 1 2 in. (114 mm) in Thickness
July 1, 2026 - ASTM International

4.1 Personnel Qualification-Personnel utilizing reference radiographs to this standard shall be qualified to perform radiographic interpretation in accordance with a nationally or internationally recognized NDT personnel qualification practice or standard and certified by the employer or certifying...

ASTM D5994/D5994M-26 - Standard Test Method for Measuring the Thickness of Geomembranes
April 1, 2026 - ASTM International

1.1 This test method covers a procedure to measure the thickness of smooth geomembranes and core thickness of textured geomembranes. 1.2 This test method does not provide thickness values for geomembranes under variable normal stresses. 1.3 The values stated in either SI units...

ASTM B352/B352M-26 - Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application
July 1, 2026 - ASTM International

1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The products covered in this specification include the following forms and sizes: 1.3.1 Sheet, 24 in. [600...

ASTM E390-20(2026) - Standard Reference Radiographs for Steel Fusion Welds
July 1, 2026 - ASTM International

1.1 This standard provides reference radiographs for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material. The reference radiograph films are an adjunct to this standard and must be purchased separately from ASTM...

ASTM D7192-26 - Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
July 1, 2026 - ASTM International

1.1 This test method covers the determination of puncture properties of plastic films, over a range of test velocities. 1.1.1 ASTM Terminology Standard D883 has defined film as having a thickness not greater than 0.25 mm. Plastic materials having a thickness above this limit are not...

ASTM E1648-20(2026) - Standard Reference Radiographs for Examination of Aluminum Fusion Welds
July 1, 2026 - ASTM International

1.1 These reference radiographs illustrate various types and severity levels of discontinuities in aluminum fusion welds that may be revealed by radiographic examination. These reference radiographs do not specify the acceptable level of these discontinuities, rather they provide a visual reference...

ASTM E242-15(2026) - Standard Reference Radiographs for Appearances of Radiographic Images as Certain Parameters are Changed
July 1, 2026 - ASTM International

1.1 This document describes the appearance of a radiographic image where fundamental components of image quality are changed, that is, variables such as whether an X-ray or gamma ray source was used, the characteristics of the radiographic film (gradient, granularity, and developing conditions) and...

ASTM D4748-26 - Standard Test Method for Determining the Thickness of Bound Pavement Layers Using Ground Penetrating Radar
April 1, 2026 - ASTM International

1.1 This test method covers the nondestructive determination of the thickness of bound pavement layers using ground penetrating radar (GPR). 1.2 This test method may not be suitable for application to pavements which exhibit increased conductivity due to the increased attenuation of the...

ASTM E1955-20(2026) - Standard Radiographic Examination for Soundness of Welds in Steel by Comparison to Graded ASTM Reference Radiographs
July 1, 2026 - ASTM International

1.1 This standard covers requirements for radiographic examination for soundness of welds in fabricated steel by comparison to selected severity levels of Reference Radiographs E390, Vol II. The base material varies from greater than 0.25?in. to 3 in. (6.4?mm to 76 mm) inclusive in thickness...

ASTM B163-26 - Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
July 1, 2026 - ASTM International

1.1 This specification covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. 1.2 This specification covers outside diameter and average wall, or outside diameter and minimum wall tube. 1.2.1 The sizes covered by this specification...

ASTM D6524/D6524M-26 - Standard Test Method for Measuring the Resiliency of Turf Reinforcement Mats (TRMs)
July 1, 2026 - ASTM International

5.1 Resiliency may be used to control the quality of many TRMs. Resiliency may be indicative of a TRM's ability to retain original configuration after exposure to the stresses which may be exerted during manufacture, shipping, and installation. Resiliency is not generally indicative of field...

ASTM E1320-20(2026) - Standard Reference Radiographs for Titanium Castings
July 1, 2026 - ASTM International

1.1 The reference radiographs provided in the adjunct to this standard are reproductions of original radiographs and are supplied as a means for establishing some of the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination. Use of...

ASTM E155-20(2026) - Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
July 1, 2026 - ASTM International

1.1 These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings. The castings illustrated are in thicknesses of 1/4 in. (6.35 mm) and 3/4 in. (19.1 mm). The reference radiograph films are an adjunct to this...

ASTM E592-20(2026) - Standard Guide to Obtainable ASTM Equivalent Penetrameter Sensitivity for Film Radiography of Steel Plates 14 to 2 in. (6 to 51 mm) Thick with X-Rays and 1 to 6 in. (25 to 152 mm) Thick with Cobalt-60
July 1, 2026 - ASTM International

1.1 This guide to obtainable equivalent penetrameter sensitivity covers the minimum penetrameter thicknesses for which the image of the 1T and 2T holes is visible for a few practical radiographic conditions using industrial X-ray film. The values represent near optimum sensitivity for flat...

ASTM E3185-21(2026) - Standard Digital Reference Images for Tin Bronze Castings
July 1, 2026 - ASTM International

4.1 Reference images for tin bronze and related alloy castings are intended to be used as a guide to the recognition of common discontinuities and their differentiation both as to type and severity level. Discontinuity types most common to these alloys are illustrated. For reference, descriptions...

ASTM D4713-12(2026) - Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems
June 1, 2026 - ASTM International

4.1 Nonvolatile content of printing inks is useful for specification acceptance between the producer and the user. 4.2 In order to obtain accurate results for heatset systems within the specified 3?h heating time, the specimen film thickness must be less than 100 g/m2, and the oven must have...

ASTM D6846-02(2026) - Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
June 1, 2026 - ASTM International

4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it...

Advertisement