4.1 General-Most thickness gauges are not applicable to all combinations of coating-substrate thicknesses and materials. The limitations of a particular instrument are generally delineated by its manufacturer. The substrate material and coating combination to be measured as well as...
1.1 This test method covers the determination of pile thickness of finished multilevel pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the...
1.1 These reference radiographs illustrate various categories, types, and severity levels of discontinuities occurring in steel castings that have section thicknesses up to 2 in. (50.8 mm) (see Note 2). The reference radiograph films are an adjunct to this standard and must be purchased...
4.1 Personnel Qualification-Personnel utilizing reference radiographs to this standard shall be qualified to perform radiographic interpretation in accordance with a nationally or internationally recognized NDT personnel qualification practice or standard and certified by the employer or certifying...
1.1 This test method covers a procedure to measure the thickness of smooth geomembranes and core thickness of textured geomembranes. 1.2 This test method does not provide thickness values for geomembranes under variable normal stresses. 1.3 The values stated in either SI units...
1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The products covered in this specification include the following forms and sizes: 1.3.1 Sheet, 24 in. [600...
1.1 This standard provides reference radiographs for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material. The reference radiograph films are an adjunct to this standard and must be purchased separately from ASTM...
1.1 This test method covers the determination of puncture properties of plastic films, over a range of test velocities. 1.1.1 ASTM Terminology Standard D883 has defined film as having a thickness not greater than 0.25 mm. Plastic materials having a thickness above this limit are not...
1.1 These reference radiographs illustrate various types and severity levels of discontinuities in aluminum fusion welds that may be revealed by radiographic examination. These reference radiographs do not specify the acceptable level of these discontinuities, rather they provide a visual reference...
1.1 This document describes the appearance of a radiographic image where fundamental components of image quality are changed, that is, variables such as whether an X-ray or gamma ray source was used, the characteristics of the radiographic film (gradient, granularity, and developing conditions) and...
1.1 This test method covers the nondestructive determination of the thickness of bound pavement layers using ground penetrating radar (GPR). 1.2 This test method may not be suitable for application to pavements which exhibit increased conductivity due to the increased attenuation of the...
1.1 This standard covers requirements for radiographic examination for soundness of welds in fabricated steel by comparison to selected severity levels of Reference Radiographs E390, Vol II. The base material varies from greater than 0.25?in. to 3 in. (6.4?mm to 76 mm) inclusive in thickness...
1.1 This specification covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. 1.2 This specification covers outside diameter and average wall, or outside diameter and minimum wall tube. 1.2.1 The sizes covered by this specification...
5.1 Resiliency may be used to control the quality of many TRMs. Resiliency may be indicative of a TRM's ability to retain original configuration after exposure to the stresses which may be exerted during manufacture, shipping, and installation. Resiliency is not generally indicative of field...
1.1 The reference radiographs provided in the adjunct to this standard are reproductions of original radiographs and are supplied as a means for establishing some of the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination. Use of...
1.1 These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings. The castings illustrated are in thicknesses of 1/4 in. (6.35 mm) and 3/4 in. (19.1 mm). The reference radiograph films are an adjunct to this...
1.1 This guide to obtainable equivalent penetrameter sensitivity covers the minimum penetrameter thicknesses for which the image of the 1T and 2T holes is visible for a few practical radiographic conditions using industrial X-ray film. The values represent near optimum sensitivity for flat...
4.1 Reference images for tin bronze and related alloy castings are intended to be used as a guide to the recognition of common discontinuities and their differentiation both as to type and severity level. Discontinuity types most common to these alloys are illustrated. For reference, descriptions...
4.1 Nonvolatile content of printing inks is useful for specification acceptance between the producer and the user. 4.2 In order to obtain accurate results for heatset systems within the specified 3?h heating time, the specimen film thickness must be less than 100 g/m2, and the oven must have...
4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it...