loading
GME B 040 1111 - Thrust Bearing Grease
February 3, 1987 - GME
A description is not available for this item.
General guide to the choice of thrust bearing type.
October 1, 2002 - ESDU

ESDU 67033 provides a guide in the early stages of design to the choice of the type of thrust bearing that is most likely to give the required performance. It is emphasised that general guidance only is provided and, in particular cases, other considerations may affect the final...

MIL-T-29026 - TRAINING AID, MOCKUP, KINGSBURY THRUST BEARING
NPFC
A description is not available for this item.
ASTM F2590-06(2022) - Standard Specification for Bearing, Roller, Thrust, Two Channeled Race Surface, Rigid or Flat Seat Type
January 1, 2022 - ASTM International

This specification covers requirements for rigid or flat seat type, two channeled race surface, thrust roller bearings intended for use in slow rotating or oscillating applications where pure thrust loads are applied. The thrust bearing shall be made of the specified...

ASTM B439-25 - Standard Specification for Iron-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated)
September 1, 2025 - ASTM International

This specification covers the standard requirements for porous metallic sleeve, flange, thrust, and spherical iron-base bearings that are produced from mixed metal powder metallurgy technology and then impregnated with oil to supply operating lubrication. Porous iron-base bearings shall be...

ASTM B438-25 - Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated)
September 1, 2025 - ASTM International

1.1 This specification covers porous metallic sleeve, flange, thrust, and spherical bronze-base bearings that are produced from mixed metal powders utilizing powder metallurgy (PM) technology and then impregnated with oil to supply operating lubrication. 1.2 Included are the specifications...

A-A-52491 - BEARING, GROOVED, BALL, THRUST: INCH AND METRIC SIZES, RACE SURFACE RIGID OR FLAT SEAT TYPE
April 18, 2018 - NPFC

This CID covers the requirements for a thrust ball bearing, referred to herein as "bearing". It consists of two hardened and ground washers (thrust plates) enclosing a complement of precision ground and lapped balls and. separated by a cage or retainer. The...

ISO 22423 - Foil bearings - Performance testing of foil thrust bearings - Testing of static load capacity, bearing torque, friction coefficient and lifetime
January 1, 2019 - ISO

This document specifies the method for comparing performance evaluation results for a foil thrust bearing that supports load with aerodynamic force generated by the rotation of a driving shaft and lubricates using air, not lubricating oil. The test procedure explained in this document...

ASTM B103/B103M-23 - Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar
October 1, 2023 - ASTM International

This specification covers plate, rolled bar, sheet, and strip of copper-tin alloy (phosphor bronze plate), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze). Copper alloys covered include UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180,...

A-A-52414 - BEARING, ROLLER, THRUST
NPFC
A description is not available for this item.
MIL-B-17380 - BEARING, ROLLER, THRUST
NPFC
A description is not available for this item.
QPL-AS81819 - Bearing, Plain, (Self-Aligning, Sleeve and Thrust), Self-Lubricating, High Speed Oscillation
March 18, 2021 - NPFC

QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION SAE-AS81819 Bearing, Plain, (Self-Aligning, Sleeve and Thrust), Self-Lubricating, High Speed Oscillation This QPL has been prepared for use by or for the Government in the acquisition of products covered by...

ISO 12130-1 - Plain bearings — Hydrodynamic plain tilting pad thrust bearings under steady-state conditions — Part 1: Calculation of tilting pad thrust bearings
April 1, 2021 - ISO

This document specifies a calculation method for oil-lubricated hydrodynamic plain bearings with complete separation of the thrust collar and tilting pad thrust bearing surfaces by a film of lubricant. This document applies to plain thrust bearings with tilting-type...

ASTM F2590-06(2013) - Standard Specification for Bearing, Roller, Thrust, Two Channeled Race Surface, Rigid or Flat Seat Type
May 1, 2013 - ASTM International

This specification covers requirements for rigid or flat seat type, two channeled race surface, thrust roller bearings intended for use in slow rotating or oscillating applications where pure thrust loads are applied. The thrust bearing shall be made of the specified...

ISO 12129-2 - Plain bearings - Tolerances - Part 2: Tolerances on form and position and surface roughness for shafts and thrust collars
April 1, 2019 - ISO

This document specifies tolerances on form and position as well as the surface roughness of shafts, flanges and thrust collars as used in plain bearing units. It is applicable to journal or thrust plain bearing units or to a combination of both, installed either...

ASTM F2590-06e1 - Standard Specification for Bearing, Roller, Thrust, Two Channeled Race Surface, Rigid or Flat Seat Type
June 1, 2006 - ASTM International

This specification covers requirements for rigid or flat seat type, two channeled race surface, thrust roller bearings intended for use in slow rotating or oscillating applications where pure thrust loads are applied. The thrust bearing shall be made of the specified...

MS 17102 - BEARING, BALL, THRUST, METRIC, SELF-ALIGNING
NPFC
A description is not available for this item.
MS 21783 - BEARING, WASHER, THRUST, SINTERED BRONZE, OIL IMPREGNATED
NPFC
A description is not available for this item.
Advertisement