3.1 Titanium dioxide is used in rubber compounding as a colorant to impart whiteness to any desired end product. It is used in sidewalls of automobile tires. 3.2 It is chemically inert and slightly basic with a pH of 7.0 to 8.0. The free-chalking, weathering properties of anatase...
1.1 This specification covers the general requirements for the 225/45R17 94H XL radial standard reference test tire. The tire covered by this specification is primarily for use as a reference tire for abrasion rate evaluations of snow, special use tires bearing any of...
1.1 This specification covers the general requirements for the 225/45R17 94V XL radial standard reference test tire. The tire covered by this specification is primarily for use as a reference tire for abrasion rate evaluations of normal and special use tires not bearing...
4.1 This guide provides information to assist engineers with the design requirements and construction guidelines for paving an open-graded friction course (OGFC) surface layer. An OGFC is primarily used to improve the skid resistance and wear resistance of an asphalt pavement by providing an escape...
5.1 This test method establishes a standard procedure for the test and provides data that can be related to the force required to unseat the bead of a tire inflated with a specified pressure from the rim. This test method does not establish performance limits or tolerances for tire...
3.1 In accordance with Specification D2227, shipments of TSR10 and TSR20 must meet a minimum initial Wallace plasticity (Po) of 30 to be accepted. However, even with this minimum restriction, the uncured viscoelastic or "processability" properties are allowed to vary greatly. This variation in...
1.1 This test method covers the measurement of the electrical resistance between the wheel of a mounted and inflated tire-wheel assembly and a flat conducting surface in loaded contact with the tire. 1.2 This test method specifies procedures and equipment such that electrical...
5.1 The pyrolysis of waste tires produces, along with recovered Carbon Black, Tire Pyrolysis Oil and Other Rubber Pyrolysis Co-Products. 5.2 TPO can be used, either directly or through further processing, as an energy source or as a feedstock in various industries (please see Appendix...
1.1 This specification covers the general requirements for the 225/75R16C 116/114S radial light truck (or European light duty vehicle) standard reference test tire. The tire covered by this specification is primarily for use as a reference tire for braking traction, snow...
3.1 In Annex A1, the interim product category rules (PCR) that shall be followed to create cradle-to-gate lifecycle assessments (LCA) for recovered carbon black (rCB) are given. The background process to be followed to create the LCA is not included in this practice. Please refer to ISO 14040 and...
1.1 This practice provides the instructions and nomenclature to evaluate the wear features of the tread pattern on a tire for some intermediate state prior to wear out. 1.2 A tire may be characterized by certain worn tread pattern conditions that are collectively referred to as...
1.1 This specification covers the general requirements for the 245/70R19.5 136/134M radial truck standard reference test tire SW. The tire covered by this specification is primarily for use as a reference tire for braking traction and snow traction but may also be used for...
1.1 This specification covers the general requirements for the 245/70R19.5 136/134M radial truck standard reference test tire. The tire covered by this specification is primarily for use as a reference tire for braking traction, snow traction, and wear performance evaluations,...
5.1 This test method is designed to assess the relative purity of production PPDs. These additives are primarily used as antiozonants for tires and other rubber or polymeric products. 5.2 Since the results of this test method are based on area normalization, it assumes that all components...
1.1 These test methods cover the testing of cords made from steel that are specifically designed for use in the reinforcement of pneumatic tires. By agreement, these test methods can be used to test similar cords or filaments used for reinforcing other rubber products. The steel cords shall...
5.1 This standard practice establishes a method for conducting accelerated laboratory aging of radial passenger or light truck tires, or both, in an oven. 5.2 The goal of this practice is to define a scientifically valid protocol for the accelerated laboratory aging of a tire such...
1.1 This standard covers the testing of industrial yarns wholly made of manufactured organic-based fibers; twisted cords made of these yarns; fabrics woven from these twisted cords; and other structures made specifically for use in manufacture of pneumatic tires. 1.1.1 These test methods can...
1.1 This test method covers the determination of fatigue of tire cords in rubber due to compression or extension, or both, using a disc fatigue tester. The fatigue is measured as a loss in strength. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as...
1.1 These test methods cover the determination of the adhesion strength between plies of fabric bonded with rubber or the adhesion of the rubber layer in articles made from rubber attached to other material. They are applicable only when the adhered surfaces are approximately plane or uniformly...
4.1 Tests for dynamic fatigue are designed to simulate the continually repeated distortions received in service by many rubber articles, such as tires, belts, footwear, and molded goods. 4.1.1 These distortions may be produced by extension, compressive, and bending forces or combinations...
Narrow Your Results