This document provides requirements for the design, fabrication, transportation, installation, modification, and structural integrity management for the topsides structure for an oil and gas platform; API 2TOP complements API 2A-WSD, API 2A-LRFD, ISO 19903, API 2FPS, API 2T, ISO 19905-1, and API...
This specification covers hot-, cold-, or both hot- and cold-rolled hafnium rods and wires in either one of two grades. All grades should be in the recrystallization annealed condition unless specified otherwise. The materials should be made from ingots produced by vacuum melting in an electron...
1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method...
This specification covers the requirements for disposable glass culture tubes for use in culturing applications. Disposable glass culture tubes shall be made of type I (borosilicate) or type II (soda-lime) glass. Tube design shall be of one-piece construction. Other requirements shall include...
5.1 Significance of this Guide: 5.1.1 Continuous improvement (CI) is a fundamental element of an operation's quality management efforts. When CI is practiced daily from the top down through the organization, the other elements of quality management fall into place. 5.1.2 CI principles are...
1.1 This test method covers determination of the mass percent of asphaltenes as defined by insolubility in normal-heptane solvent. It is applicable to all solid and semi-solid petroleum asphalts containing little or no mineral matter, to gas oils, to heavy fuel oils, and to crude petroleum that has...
1.1 This specification covers floor covering having a vinyl plastic wear layer with backing. Products may also contain non-PVC specialty performance top layer(s) or intermediate layer(s), or both. 1.2 Two types of floor covering based on binder content are covered. The floor covering is...
5.1 Due to hydraulic pressure that may be present on some applications, engineers need to understand the capability of these products to resist this pressure. This test allows engineers to compare products and verify pullout strength. 5.2 Hydraulic pullout resistance is a function of locking...
This specification covers preformed open-cell sponge rubber gaskets, for use in new or reconditioned pails or drums, of the following classes: Class A and Class B, each divided into Grade 1, Grade 2, and Grade 3. Cellular sponge rubber gaskets shall be made by incorporating a blowing agent into the...
This specification covers heavy-duty ranges that use gas or electrical heat sources, or both, for cooking food in the commercial and institutional food service establishments. Types: type I-electric range top with electric oven; type I-electric range top with gas-fired oven; type...
4.1 The bi-directional axial compressive load test provides separate, direct measurements of the axial capacity mobilized above an embedded jack assembly and element end bearing plus any axial capacity mobilized below the jack assembly. The maximum mobilized axial capacity equals two times the...
4.1 Morphological analysis used for facial comparison benefits from the utilization of consistent terminology and methodology. This practice provides a standard set of facial components, characteristics, and descriptors to be used in conjunction with a systematic method of analysis for facial image...
1.1 These test methods cover the ability of window assemblies of various types to restrain, delay, or frustrate forced entry. 1.2 For purposes of these test methods, window assemblies are defined as described in 1.2.1 - 1.2.5 and as shown in Fig. 1. Window assemblies with a combination of operable...
This specification covers griddles which utilize gas or electrical heat sources, or both, for cooking food in the commercial and institutional food service establishments. Griddles covered by this specification are classified by type, size, style, and electrical class. Type: type 1 - for counter...
4.1 Based on the measurements of strain and acceleration close to the pile top, possibly combined with those from accelerometers or strain transducers located further down the pile, this test method assesses the pile top velocity and force in response to an axial impact force. 4.2 The...
1.1 This test method covers the energy consumption and cooking performance of double-sided griddles. The food service operator can use this evaluation to select a double-sided griddle and understand its energy efficiency and productivity. 1.2 This test method is applicable to thermostatically...
1.1 This specification covers child carriers that mount to the rear of bicycles in order to transport children or accessory loads with a maximum weight of 18 kg (40 lb). This specification does not apply to child carriers that mount in front of the handlebars, or to the top tube, head tube,...
1.1 This specification covers the basic requirements for a corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic topcoat, depending on the specific requirements. 1.2 The coating may be specified with basecoat only, or with the...
4.1 This test method covers the determination of the air content of freshly mixed concrete. It measures the air contained in the mortar fraction of the concrete, but is not affected by air that may be present inside porous aggregate particles. 4.1.1 Therefore, this is the appropriate test to...
This specification covers standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension (pull-off method). This test method is suitable for both field and laboratory use to determine one or more of...
Narrow Your Results