5.1 In the absence of water, the crude oil is noncorrosive. However, trace amounts of water and sediment have the potential to create corrosive situations during crude oil handling or transport if such materials accumulate and persist on steel surfaces. Test Methods D473 and D4006 provide...
1.1 This test method is applicable to determine the pH of water samples with a conductivity of 2?μS/cm to 100?μS/cm over the pH range of 3 to 11 and is frequently used in power generation low conductivity samples. pH measurements of water of low conductivity are problematic....
1.1 Purpose and Application-This guide summarizes the equipment, field procedures, and interpretation methods for the assessment of subsurface materials using the electromagnetic (EM) metal detection method and therefore in this guide the term "metal detector" is used to refer to an EM metal...
1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade mixed oxides, (U, Pu)O2, powders and pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Uranium in the...
5.1 This test method is useful for determining the quantity of one or more isotopes present in a container like in the context of process monitoring, safeguard and inventory of nuclear materials. 5.1.1 Calorimetry is considered to be an established NDA method for the measurement of tritium. It is...
1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade plutonium dioxide powders and pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Plutonium Sample...
1.1 This test method covers the on-line and in-line determination of dissolved ozone (DO3) in low conductivity water in the range from 0.001 mg/L to 5.0 mg/L DO3 and conductivity <100 μS/cm, typical of pharmaceutical and microelectronics pure waters. DO3 is detected by correlating the...
5.1 The laboratory weathering procedure will generate data that can be used to: (1) determine whether a solid material will produce an acidic, alkaline, or neutral effluent, (2) identify solutes in the effluent that represent dissolved weathering products formed during a specified period of time,...
1.1 These test methods cover the determination of the electrical conductivity and resistivity of water. The following test methods are included: Range Sections Test Method A-Field and Routine Laboratory 10 to 200?000 12 to 18 ?Measurement of Static (Non-Flowing) Samples ?μS/cm Test Method...
5.1 In the absence of water, the crude oil is noncorrosive. However, trace amounts of water and sediment have the potential to create corrosive situations during crude oil handling or transport if such materials accumulate and persist on steel surfaces. Test Methods D473 and D4006 provide...
5.1 Conductivity measurements are typically made on samples of moderate to high ionic strength where contamination of open samples in routine laboratory handling is negligible. Under those conditions, standard temperature compensation using coefficients of 1 to 3?% of reading per degree...
This document specifies a method for the determination of traces of perchlorate in mineral fertilizers by ion chromatography and conductivity detection (IC-CD).
4.1 This test method provides a rapid means of determining the steady-state thermal transmission properties of thermal insulations and other materials with a high level of accuracy when the apparatus has been calibrated appropriately. 4.2 Proper calibration of the heat flow meter apparatus requires...
1.1 This practice2 covers the types of and preparation of containers found most suitable for the handling of aviation fuel samples for the determination of critical properties affected by trace contamination. 1.2 The values stated in SI units are to be regarded as standard. No other units of...
5.1 The hydrocarbon component distribution of gaseous mixtures is often required for end-use sale of this material. Applications such as chemical feedstock or fuel require precise compositional data to ensure uniform quality. Trace amounts of some hydrocarbon impurities in these materials...
1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets to determine compliance with specifications. 1.2 Units-The values stated in SI units are to be regarded as standard. The values given in...
1.1 This test method covers the on-line determination of trace amounts of sodium in water using an ion-selective electrode. 1.2 This test method is based on on-line application of the sodium ion electrode as reported in the technical literature (1-3).2 It is generally applicable over the...
5.1 Concepts-This guide summarizes the equipment, field procedures, and data processing methods used to interpret geologic conditions, and to identify and provide locations of geologic anomalies and man-made objects with the GPR method. The GPR uses high-frequency EM waves (from 10 to 3000 MHz) to...
1.1 These test methods cover procedures for the analysis of sintered gadolinium oxide-uranium dioxide pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Section Carbon (Total) by Direct Combustion-Thermal Conductivity Method 2...
5.1 Factors that may influence the thermal-transmission
Narrow Your Results