1.1 This specification covers welded austenitic, ferritic, martensitic, and austenitic-ferritic duplex stainless steel mechanical tubing intended for use in ornamental, structural, exhaust, and other applications where appearance, mechanical properties, or corrosion resistance is needed. The...
1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI units are to be...
1.1 This specification covers minimum-wall-thickne
1.1 This specification covers cold-formed welded unannealed austenitic, ferritic-martensitic
1.1 This specification covers 0.070 in. wall thickness crosslinked polyethylene (PEX) tubing that is outside diameter controlled, and intended for non-potable radiant heating applications for pressures up to 75 psig in sizes 5/8 NTS (nominal tubing size) and 7/8 NTS....
1.1 This specification covers metal insert fittings and copper crimp rings, or alternate stainless steel clamps, for use with cross-linked polyethylene (PEX) tubing in Nominal Tubing Size (NTS) 3/8 , 1/2 , 5/8 , 3/4 , 1, 1 1/4 , 11/2 , and 2 nominal sizes that meet the...
1.1 This specification covers minimum-wall-thickne
1.1 This specification covers minimum-wall-thickne
1.1 This specification covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface condensers, evaporators, and heat exchangers, as follows: 1.1.1 Grade 1-UNS R50250. Unalloyed titanium, 1.1.2 Grade 2-UNS R50400. Unalloyed titanium, 1.1.2.1 Grade 2H-UNS...
1.1 This test method, commonly referred to as the Cummins ISB Viscosity Test, covers the utilization of a 5.9?L diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to soot induced viscosity increase. 1.2 The values stated in SI units are to be...
1.1 This specification covers metal insert fittings and copper crimp rings, or alternate stainless steel clamps, for use with cross-linked polyethylene (PEX) tubing in Nominal Tubing Size (NTS) 3/8 , 1/2 , 5/8 , 3/4 , 1, 1 1/4 , 11/2 , and 2 nominal sizes that meet the...
1.1 This specification covers polyethylene (PE 4710) electrofusion fittings for use with outside diameter-controlled crosslinked polyethylene (PEX) pipe and tubing, covered by Specifications F876, F2788/F2788M, F2905/F2905M and F2968/F2968M. As stated in these PEX standards, the PEX pipe and...
1.1 This specification2 covers minimum-wall-thickne
1.1 This specification covers stainless steel clamps for use with five sizes of insert fittings that comply with F1807 or F2159, and cross-linked polyethylene (PEX) plastic tubing that complies with F876 and for use with polyethylene of raised temperature (PE-RT) tubing that...
This specification covers mineral fiber pipe insulation that are formed into hollow cylinders for standard pipe and tubing sizes. The pipe insulation may be molded or precision v-grooved with one or more walls split longitudinally and used up to a specified temperature. The materials...
1.1 This speci?cation describes the production of welded copper and copper alloy tubes with a longitudinal seam free of ?ller metal produced from sheet or strip up to 1.5 in. (38.1?mm), in diameter for use in surface condensers, evaporators, heat exchangers, and general engineering applications....
1.1 This specification covers grades of stainless steel tubing in sizes under 1/2 down to 0.050 in. (12.7 to 1.27 mm) in outside diameter and wall thicknesses less than 0.065 in. down to 0.005 in. (1.65 to 0.13 mm) for general corrosion-resisting and low- or high-temperature service,...
1.1 This test method, commonly referred to as the Cummins ISB Test, covers the utilization of a modern, 5.9?L, diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to valve-train wear. 1.2 The values stated in SI units are to be regarded as...
This specification covers seamless stainless tubing for use in mechanical applications where corrosion-resistant or high-temperature strength is needed. The steel may be cast in ingots or may be strand cast. When steel of different grades is sequentially strand cast, identification of the...
Narrow Your Results