This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon black,...
This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and...
1.1 This specification covers welded austenitic, ferritic, martensitic, and austenitic-ferritic duplex stainless steel mechanical tubing intended for use in ornamental, structural, exhaust, and other applications where appearance, mechanical properties, or corrosion resistance is needed. The...
This specification covers crosslinked polyethylene (PEX) tubing that is outside diameter controlled, made in standard thermoplastic tubing dimension ratios, and pressure rated for water at three temperatures. This specification covers one PEX tubing material in one standard...
1.1 This guide describes general procedures for squeeze-off of polyethylene gas pressure pipe and tubing as recommended in GRI-92/0147.1, GRI-92/0147.2, and OTD Project 2.14c / GTI Project 22245. Note 1: Operator squeeze-off procedures should be developed and qualified in accordance with...
1.1 This specification covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface condensers, evaporators, and heat exchangers, as follows: 1.1.1 Grade 1-UNS R50250. Unalloyed titanium, 1.1.2 Grade 2-UNS R50400. Unalloyed titanium, 1.1.2.1 Grade 2H-UNS...
1.1 This specification covers cold-formed welded unannealed austenitic, ferritic-martensitic
1.1 This practice describes procedures for making butt fusion joints with crosslinkable polyethylene (CX-PE) pipe and tubing which is less than 30 % crosslinked at the time of joining. This practice shall not be applied to crosslinked products, that is PEX pipe or tubing or to CX-PE...
This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications. Requirements cover workmanship,...
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications....
1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI units are to be...
This specification covers the chemical, physical, mechanical, and metallurgical requirements for wrought nickel-titanium bar, flat rolled products, and tubing containing nominally 54.5 % to 57.0 % nickel and used for the manufacture of medical devices and surgical implants. The material...
This specification covers the requirements, test methods, and markings for crosslinked polyethylene (PEX) tubing with a polymeric oxygen barrier layer, made in one standard dimension ratio (SDR 9), and distribution system components intended for hydronic heating and cooling applications up...
1.1 This specification covers polyethylene (PE 4710) electrofusion fittings for use with outside diameter-controlled crosslinked polyethylene (PEX) pipe and tubing, covered by Specifications F876, F2788/F2788M, F2905/F2905M and F2968/F2968M. As stated in these PEX standards, the PEX pipe and...
5.1 Test Method A is the required flammability test for: crosslinked chlorinated polyolefin heat-shrinkable tubing for electrical insulation (Specification D2903), crosslinked poly(vinylidene fluoride) heat-shrinkable tubing for electrical insulation (Specification D3144), and...
This specification covers seamless medium-carbon steel boiler and superheater tubes. The specification also covers minimum-wall-thickne
This specification covers requirements for solvent cements for chlorinated poly(vinyl chloride) (CPVC) plastic pipe, tubing, and socket-type fittings. Solvent cement shall be a CPVC resin-based solution, shall be free-flowing, shall show no gelation or stratification, and shall not contain...
1.1 This specification covers metal insert fittings and copper crimp rings, or alternate stainless steel clamps, for use with cross-linked polyethylene (PEX) tubing in Nominal Tubing Size (NTS) 3/8 , 1/2 , 5/8 , 3/4 , 1, 1 1/4 , 11/2 , and 2 nominal sizes that meet the requirements...
1.1 This specification covers stainless steel clamps for use with five sizes of insert fittings that comply with F1807 or F2159, and cross-linked polyethylene (PEX) plastic tubing that complies with F876 and for use with polyethylene of raised temperature (PE-RT) tubing that complies...
Narrow Your Results