loading
ASTM A388/A388M-26 - Standard Practice for Ultrasonic Examination of Steel Forgings
April 1, 2026 - ASTM International

This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of heavy steel forgings by the straight and angle-beam techniques. An ultrasonic, pulsed, reflection type of instrument shall be used and shall provide linear presentation for at least...

ASTM E1324-21(2026) - Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments
May 1, 2026 - ASTM International

1.1 This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments: 1.1.1 Power Supply Section: ??????line regulation, ???????battery discharge time, and ???????battery charge time. 1.1.2 Pulser...

ASTM E2375-26a - Standard Practice for Ultrasonic Testing of Wrought Products
March 15, 2026 - ASTM International

1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...

ASTM E1001-21(2026) - Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves
July 1, 2026 - ASTM International

1.1 This practice describes procedures for the ultrasonic examination of bulk materials or parts by transmitting pulsed, longitudinal waves through a liquid couplant into the material and observing the indications of reflected waves (see Fig. 1). It covers only examinations in which one...

ASTM E1685-20(2026) - Standard Practice for Measuring the Change in Length of Bolts Using the Ultrasonic Pulse-Echo Technique
April 1, 2026 - ASTM International

5.1 The techniques described provide for the measurement of change in length of a fastener. Such measurements are made from one end of the specimen without requiring access to the rear surface. 5.2 The Ultrasonic Pulse Echo technique is used to monitor changes in length of fasteners and as a...

ASTM B338-17(2026) - Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers
July 1, 2026 - ASTM International

This specification covers 28 grades of seamless and welded titanium alloy tubes for surface condensers, evaporators, and heat exchangers. Seamless tube shall be made from hollow billet by any cold reducing or cold drawing process that will yield a product meeting the requirements prescribed. Welded...

ASTM E2661/E2661M-26 - Standard Practice for Acoustic Emission Examination of Plate-like and Flat Panel Composite Structures Used in Aerospace Applications
July 1, 2026 - ASTM International

5.1 This AE examination is useful to detect micro-damage generation, accumulation, and growth of new or existing flaws. The examination is also used to detect significant existing damage from friction-based AE generated during loading or unloading of these regions. The damage mechanisms that can be...

ASTM E2375-26 - Standard Practice for Ultrasonic Testing of Wrought Products
January 1, 2026 - ASTM International

1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...

ASTM B381-26 - Standard Specification for Titanium and Titanium Alloy Forgings
July 1, 2026 - ASTM International

This specification covers 39 grades of annealed titanium and titanium alloy forgings as Grade F-1, Grade F-2, Grade F-2H, Grade F-3, Grade F-4, Grade F-5, Grade F-6, Grade F-7, Grade F-7H, Grade F-9, Grade F-11, Grade F-12, Grade F-13, Grade F-14, Grade F-15, Grade F-16, Grade F-16H, Grade F-17,...

ASTM E2985/E2985M-26 - Standard Practice for Determination of Metal Purity Based on Elastic Constant Measurements Derived from Resonant Ultrasound Spectroscopy
June 15, 2026 - ASTM International

1.1 This practice is intended for use with swept sine resonant ultrasound spectrometers capable of exciting, measuring, recording, and analyzing multiple whole body mechanical vibration resonant frequencies within parts exhibiting acoustical ringing in the acoustic or ultrasonic, or both,...

ASTM E1419/E1419M-26 - Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
May 1, 2026 - ASTM International

1.1 This practice provides guidelines for acoustic emission (AE) examinations of seamless pressure vessels (tubes) of the type used for distribution or storage of industrial gases. 1.2 This practice requires pressurization to a level greater than normal use. Pressurization medium may be gas or...

ASTM A1038-26 - Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method
February 15, 2026 - ASTM International

1.1 This test method covers the determination of comparative hardness values by applying the ultrasonic contact impedance method (UCI method). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1...

ASTM E494-20(2025) - Standard Practice for Measuring Ultrasonic Velocity in Materials by Comparative Pulse-Echo Method
December 1, 2025 - ASTM International

5.1 This practice describes a test procedure for the application of conventional ultrasonic methods to determine unknown ultrasonic velocities in a material sample by comparative measurements using a reference material whose ultrasonic velocities are accurately known. 5.2...

ASTM E2700-26 - Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays
January 1, 2026 - ASTM International

1.1 This practice covers ultrasonic techniques for examining welds using phased array ultrasonic methods (see Note 1 and Note 2). 1.2 This practice uses angle beams, either in S-scan or E-scan modes, primarily for butt welds and tee welds. Alternative welding techniques, such as solid...

ASTM B350/B350M-11(2026) - Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application
April 1, 2026 - ASTM International

This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. Materials covered shall be produced by multiple vacuum arc melting, or electron beam melting, or other melting processes conventionally used for reactive metals. Unless otherwise specified, ingots...

ASTM E1316-26a - Standard Terminology for Nondestructive Examinations
March 15, 2026 - ASTM International

1.1 This standard covers the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle...

ASTM E664/E664M-25 - Standard Practice for the Measurement of the Apparent Attenuation of Longitudinal Ultrasonic Waves by Immersion Method
December 1, 2025 - ASTM International

1.1 This practice covers a procedure for measuring the apparent attenuation of ultrasound in materials or components with flat, parallel surfaces using conventional pulse-echo ultrasonic flaw detection equipment in which reflected indications are displayed in an A-scan presentation. 1.2 The...

ASTM E1316-26 - Standard Terminology for Nondestructive Examinations
March 1, 2026 - ASTM International

1.1 This standard covers the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle...

ASTM B614-26 - Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
April 1, 2026 - ASTM International

This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. Grease,...

ASTM E3517/E3517M-26 - Standard Practice for Flaw Sizing using Total Focusing Method
February 1, 2026 - ASTM International

1.1 This practice covers procedures for evaluating length and vertical extent sizes of flaws in metal weldments using the post processing algorithms referred to as total focusing method (Note 1). Note 1: This practice is based on experience with ferrous and aluminum alloys. Other metallic materials...

Advertisement