This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of heavy steel forgings by the straight and angle-beam techniques. An ultrasonic, pulsed, reflection type of instrument shall be used and shall provide linear presentation for at least...
1.1 This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments: 1.1.1 Power Supply Section: ??????line regulation, ???????battery discharge time, and ???????battery charge time. 1.1.2 Pulser...
1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...
1.1 This practice describes procedures for the ultrasonic examination of bulk materials or parts by transmitting pulsed, longitudinal waves through a liquid couplant into the material and observing the indications of reflected waves (see Fig. 1). It covers only examinations in which one...
5.1 The techniques described provide for the measurement of change in length of a fastener. Such measurements are made from one end of the specimen without requiring access to the rear surface. 5.2 The Ultrasonic Pulse Echo technique is used to monitor changes in length of fasteners and as a...
This specification covers 28 grades of seamless and welded titanium alloy tubes for surface condensers, evaporators, and heat exchangers. Seamless tube shall be made from hollow billet by any cold reducing or cold drawing process that will yield a product meeting the requirements prescribed. Welded...
5.1 This AE examination is useful to detect micro-damage generation, accumulation, and growth of new or existing flaws. The examination is also used to detect significant existing damage from friction-based AE generated during loading or unloading of these regions. The damage mechanisms that can be...
1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...
This specification covers 39 grades of annealed titanium and titanium alloy forgings as Grade F-1, Grade F-2, Grade F-2H, Grade F-3, Grade F-4, Grade F-5, Grade F-6, Grade F-7, Grade F-7H, Grade F-9, Grade F-11, Grade F-12, Grade F-13, Grade F-14, Grade F-15, Grade F-16, Grade F-16H, Grade F-17,...
1.1 This practice is intended for use with swept sine resonant ultrasound spectrometers capable of exciting, measuring, recording, and analyzing multiple whole body mechanical vibration resonant frequencies within parts exhibiting acoustical ringing in the acoustic or ultrasonic, or both,...
1.1 This practice provides guidelines for acoustic emission (AE) examinations of seamless pressure vessels (tubes) of the type used for distribution or storage of industrial gases. 1.2 This practice requires pressurization to a level greater than normal use. Pressurization medium may be gas or...
1.1 This test method covers the determination of comparative hardness values by applying the ultrasonic contact impedance method (UCI method). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1...
5.1 This practice describes a test procedure for the application of conventional ultrasonic methods to determine unknown ultrasonic velocities in a material sample by comparative measurements using a reference material whose ultrasonic velocities are accurately known. 5.2...
1.1 This practice covers ultrasonic techniques for examining welds using phased array ultrasonic methods (see Note 1 and Note 2). 1.2 This practice uses angle beams, either in S-scan or E-scan modes, primarily for butt welds and tee welds. Alternative welding techniques, such as solid...
This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. Materials covered shall be produced by multiple vacuum arc melting, or electron beam melting, or other melting processes conventionally used for reactive metals. Unless otherwise specified, ingots...
1.1 This standard covers the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle...
1.1 This practice covers a procedure for measuring the apparent attenuation of ultrasound in materials or components with flat, parallel surfaces using conventional pulse-echo ultrasonic flaw detection equipment in which reflected indications are displayed in an A-scan presentation. 1.2 The...
1.1 This standard covers the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle...
This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. Grease,...
1.1 This practice covers procedures for evaluating length and vertical extent sizes of flaws in metal weldments using the post processing algorithms referred to as total focusing method (Note 1). Note 1: This practice is based on experience with ferrous and aluminum alloys. Other metallic materials...
Narrow Your Results