ESDU 90012 discusses and illustrates the use of the energy height method to minimise time or fuel used in transferring from one (velocity, height) point to another. Energy height is an "equivalent" height that yields an "equivalent" potential energy at any point...
5.1 This test method is applicable for qualitatively evaluating coated and uncoated monolithic polycarbonate sheet material, for monitoring process control, for screening studies, and as an aid in the prediction of hardware performance when exposed to impact service conditions. 5.2 A...
Purpose. This procedure includes four purposes/methods for determination of rear closure closing behavior. Generation of a characteristic closing curve for fully latching by determination of a maximum allowable closing weight from a specified closing height. Generation of a...
This business process applies to all work at height carried out by Network Rail employees or contractors working on behalf of Network Rail. Purpose This business process enables employees who design, plan, manage and carry out work at heights to do so safely, and within the...
5.1 The impact strength values obtained on the flat sections of a building product profile are relevant only to the flat section that has been tested and these values do not necessarily indicate the impact resistance of the whole product, which is affected by the configuration of the profile...
These test methods specify procedures and apparatus used for testing and evaluating Externally Loaded Strength Training Equipment, Strength Training Benches and External Weight Storage Equipment for compliance to Specification F3105. Both design and operational...
1.1 These test methods specify procedures and apparatus used for testing and evaluating Externally Loaded Strength Training Equipment, Strength Training Benches and External Weight Storage Equipment for compliance to Specification F3105. Both design and...
5.1 This practice is applicable for qualitatively evaluating coated and uncoated monolithic polycarbonate sheet material, for monitoring process control, for screening studies, and as an aid in the prediction of hardware performance when exposed to impact service conditions. 5.2 A...
This part of ISO 6272 describes a method for evaluating the resistance of a dry film of paint, varnish or related product to cracking or peeling from a substrate when it is subjected to a deformation caused by a falling weight, with a 20-mm-diameter spherical indenter, dropped under standard...
This part of ISO 6272 describes a method for evaluating the resistance of a dry film of paint, varnish or related product to cracking or peeling from a substrate when it is subjected to a deformation caused by a falling weight, with a 20-mm-diameter spherical indenter, dropped under standard...
This standard applies to the height adjuster assembly (including knobs, buttons, fixings). PURPOSE This standard aims at specifying the performance and validation of the height adjuster system and parts.
1.1 General-This specification covers deformed and plain low-alloy steel bars in cut lengths and coils for concrete reinforcement intended for applications where restrictive mechanical properties and chemical composition are required for compatibility with controlled tensile...
5.1 Susceptibility to damage from concentrated out-of-plane impact forces is one of the major design concerns of many structures made of advanced composite laminates. Knowledge of the damage resistance properties of a laminated composite plate is useful for product development and material...
This practice is applicable for qualitatively evaluating coated and uncoated monolithic polycarbonate sheet material, for monitoring process control, for screening studies, and as an aid in the prediction of hardware performance when exposed to impact service conditions. A limitation...
1.1 General-This specification covers deformed and plain low-alloy steel bars in cut lengths and coils for concrete reinforcement intended for applications where restrictive mechanical properties and chemical composition are required for compatibility with controlled tensile...
1.1 This test method describes how the crosslink density, molecular weight between crosslinks, and number of repeat units between crosslinks in ultra high molecular weight polyethylene (UHMWPE) crosslinked by ionizing radiation or by chemical means can be determined by...
This specification covers one type of height reference unit used in the Gun Direction Computers: Ml5 and Ml5C which are a part of the Field. Artillery Fire Control Systems: M35 and" M35C. The height reference unit is used to resolve a mechanical input of ORIGIN into two...
This part of ISO 6272 describes a method for evaluating the resistance of a dry film of paint, varnish or related product to cracking or peeling from a substrate when it is subjected to a deformation caused by a falling weight, with a 20-mm-diameter spherical indenter, dropped under standard...