This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings, Type B...
1.1 These test methods cover procedures for the chemical analysis of metallic zinc powder in the form commercially known as zinc dust for use as a pigment in paints. 1.2 The analytical procedures appear in the following order: Sections Moisture and Other Volatile Matter 7 Coarse...
This specification covers two types of commercial rolled zinc. Type I are coils or sheets cut from strip rolled zinc, and Type II are zinc plates such as boiler and hull plates produced by any rolling method. The products shall be produced by casting, rolling, and other...
1.1 This specification covers aluminum-base and zinc-base master alloys used to make zinc die-casting alloys. Alloy compositions specified for aluminum-base master alloys (hardeners) are designated as shown in Table 1. Alloy compositions specified for the zinc-base master...
4.1 This practice is applicable to non-chromate coatings that are colorless, colored, electrochemically applied or non-electrochemicall
1.1 This specification covers certain zinc-aluminum (Zn-Al) alloys in ingot form for re-melting for use in the production of hot-dip coatings on steel. Alloy compositions are specified below and in Table 1. ASTM Common UNS Type 5 95/5 Zn/Al Z30507 Type 10 90/10 Zn/Al Z30600 Type 15 85/15...
1.1 This specification covers the general requirements that, unless otherwise specified in the product specification, apply to steel sheet in coils and cut lengths, metallic-coated on continuous lines by the hot-dip process. The product is intended for applications requiring corrosion resistance....
1.1 This specification covers steel sheet used in the manufacture of corrugated steel pipe for storm sewers, culverts, drains, and similar uses. The sheet is metallic coated by the hot-dip process. Material for this use is furnished in coils, flat in cut lengths, and corrugated in cut lengths. Many...
1.1 This specification covers various designs of welded wire mesh or twisted (woven) hexagonal wire mesh, zinc coated before fabrication, to be used as reinforcement for the concrete applied in the manufacture of negative buoyancy pipe needed for laying pipe in marshes or in water. The mesh...
1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of dies and molds from the alloys as shown in Table 1. 1.2 This specification presents requirements for zinc alloys suitable for the production of sand cast or plaster cast forming...
1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in Table 1. 1.2 Slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp...
This specification covers zinc-coated fence fabric intended for enclosure of poultry, or to prevent entry into special areas. It is available in three styles as: poultry netting; poultry-and-garden fence fabric; and chick fence fabric. The zinc used for the coating shall be any grade...
This specification covers the standard requirements for iron wire with Class A, Class B, and Class C zinc coatings suitable for use in telephone, telegraph, and signal transmission lines. The zinc used for the coatings shall be of any grade while the base metal shall be made by any...
1.1 This test method is intended as a means of determining the corrosive effects of aircraft maintenance chemicals on low-embrittling zinc-nickel plating used on aircraft high-strength steel, under conditions of total immersion by quantitative measurements of weight change. Aircraft...
5.1 Some oils are formulated with organo-metallic additives which act as detergents, antioxidants, antiwear agents, and so forth. Some of these additives contain one or more of these elements: barium, calcium, phosphorus, sulfur, and zinc. These test methods provide a means of determining...
This specification covers the requirements for extruded leaded-brass angles, channels, and other architectural shapes of solid cross section produced in Copper Alloy UNS Nos. C38000 and C38500. The material shall conform to the chemical composition specified. For copper alloys in which zinc...
1.1 These test methods cover chemical and physical tests for zinc oxide that are considered to be important to its use in rubber compounding. 1.2 The tests appear in the following order: ??Test Section Zinc Oxide 5 Lead and Cadmium 6 Sulfur 7 Heat Loss 8 Surface Area 9 Sieve Residue...
This specification covers requirements for steel reinforcing bars, with protective zinc or zinc-alloy coatings applied by the continuous hot-dip process. Continuous hot-dip galvanizing refers to the process of uninterrupted passage of long lengths of steel products through a molten...
4.1 The surface area of zinc-oxide in rubber can significantly affect cure activation and vulcanizate properties. 4.2 The specific surface area of zinc-oxide is usually measured by nitrogen absorption which requires the use of equipment not normally found in rubber laboratories. This...
1.1 This classification system covers the compounding material commercially known as zinc oxide. The types of zinc oxide used in the rubber industry are related to the production process used. Typical chemical and physical properties are included. 1.2 This international standard was...
Narrow Your Results