FOREWORD The SMACNACADSTANDARD(SC
1.1 This practice provides information about utilizing human digital modeling in the design and evaluation of exoskeletons. This practice specifies: 1.1.1 Basic terminology, definitions, principles, methods, inputs, and expected outputs of digital human modeling (DHM) methods. 1.1.2 Principles of...
1.1 This practice covers a uniform procedure for the examination of castings by the computed tomography (CT) technique including both cone and fan beam. The requirements expressed in this practice are intended to control the quality of the nondestructive examination by CT and are not intended for...
3.1 Standard nomenclature shall be used to facilitate communication between designers, suppliers, and users of HVAC ventilation ductwork components. 3.2 Standard design parameters shall be used to define ventilation ductwork shapes. 3.3 Standard variables for design parameters (see 2.2) are useful...
5.1 This guide applies to directed energy deposition (DED) systems and processes, including electron beam, laser beam, and arc plasma based systems, as well as applicable material systems. 5.2 Directed energy deposition (DED) systems have the following general collection of characteristics: ability...
1.1 These requirements cover an energy storage system (ESS) that is intended to receive and store energy in some form so that the ESS can provide electrical energy to loads or to the local/area electric power system (EPS) when needed. Electrochemical, chemical, mechanical, and thermal ESS are...
5.1 General: 5.1.1 This guide is intended to support PBF-LB process and parameter development, part acceptance criteria, and process control tests. 5.1.2 Flaws and Defects-Fabricating fully dense parts continues to be a challenge in AM as the process intrinsically introduces volumetric flaws into a...
This document describes the 2-D computer-aided design (CAD) template for the HPM-1 H-point machine or HPD available from SAE. The elements of the HPD include the curve shapes, datum points and lines, and calibration references. The intended purpose for this information is to provide a master...
This document describes the 3D computer-aided design (CAD) parts and file formats for the HPM-1 H-point machine available from SAE. The intended purpose for this information is to provide a master CAD reference for design and benchmarking.
1.1 This practice covers a uniform procedure for the examination of castings by the computed tomography (CT) technique. The requirements expressed in this practice are intended to control the quality of the nondestructive examination by CT and are not intended for controlling the acceptability or...
1.1 This test method is for the separation of lipids in liposomal formulations through high performance liquid chromatography (HPLC) and their quantitation using a mass-flow sensitive charged aerosol detector (CAD). 1.2 This test method is specifically for liposomal formulations containing...
This SAE Standard provides the specifications and procedures for using the H-point machine (HPM 2x) to audit vehicle seating positions. The HPM is a physical tool used to establish key reference points and measurements in a vehicle (see Figure 1 and Appendix A ). The H-point design tool (HPD) is a...
1.1 Objectives-This practice establishes and defines the processes and associated requirements for incorporating Human Systems Integration (HSI) into all phases of government and commercial ship, offshore structure, and marine system and equipment (hereafter referred to as marine system)...
This part of IEC 61188 describes the configuration of part shape data of semiconductor devices and electrical components registered in the CAD library. This document mainly describes the configuration of 2D and 3D parts shape data.
This document specifies requirements for the preparation, revision and presentation of digital product definition data, hereafter referred to as data sets, complementing existing standards. It supports two methods of application: 3D model-only and 3D model with 2D drawing in digital format. The...
This document specifies the classification of and requirements for dental casting and dental baseplate waxes together with the test methods to be employed to determine compliance with these requirements. This document does not apply to waxes supplied for additive manufacturing or...
This document is applicable to waxes used for dental casting and dental baseplates. It specifies the classification of, and requirements for such waxes together with the test methods to be employed to determine compliance with these requirements. It does not apply to waxes supplied for 3D-printing...
This document specifies requirements and test methods for intraoral cameras used in dentistry on patients for pictorial representation of oral cavities in order to support diagnosis and facilitate patient information. It specifies requirements, test methods, instructions for use and marking. This...
This document specifies the classification of and requirements for dental casting and dental baseplate waxes together with the test methods to be employed to determine compliance with these requirements. This document does not apply to waxes supplied for additive manufacturing or...
This document specifies requirements and test methods for intraoral cameras used in dentistry on patients for pictorial representation of oral cavities in order to support diagnosis and facilitate patient information. It specifies requirements, test methods, instructions for use and marking. This...
Narrow Your Results