This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Structural design of panels shall be performed in accordance with the provisions of the applicable local building code and the...
5.1 This test method is intended to simulate the corrosion process of non-ferrous metals in diesel lubricants. The corrosion process under investigation is that believed to be induced primarily by inappropriate lubricant chemistry rather than lubricant degradation or contamination. This test method...
5.1 Before proceeding with this test method, refer to the material specification for the material being tested. Any test specimen preparation, conditioning, dimensions and testing parameters required by the materials specification shall take precedence over those required by this test method. Table...
This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering...
1.1 This test method is applicable to firestop systems of various materials and construction. Firestop systems are intended for use in openings in fire-resistive walls and floors that are evaluated in accordance with Test Methods E119. 1.2 Tests conducted in conformance with this test method record...
4.1 Adequate coating thickness (mil thickness) is necessary to protect polyurethane foam from the effects of ultraviolet degradation. This guide outlines general procedures for sampling and measuring the coating thickness by using slit or core samples. 4.2 Thickness of individual lifts of sprayed...
1.1 This specification covers the chemical, mechanical, and dimensional requirements for roof and rock bolts and accessories. Addressed in this specification are double-end threaded bars; fully grouted bolts and threaded bars; mechanical anchorage devices used for point anchorage applications; roof...
1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be matt, bright, or semibright and are not less than 98?mass?% silver purity. 1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces,...
5.1 Because of its simplicity and accuracy, the polarization resistance technique has been widely used in the laboratory in numerous metal/electrolyte systems (2, 7-10). However, its application in real-size elements is not straightforward because of the need for referral to the actual polarized...
1.1 This test method covers a procedure for the determination of basic constituents in petroleum products and new and used lubricants. This test method resolves these constituents into groups having weak-base and strong-base ionization properties, provided the dissociation constants of the more...
1.1 These test methods cover standardized procedures for evaluating the cross-grain compression strength and stiffness of wood and wood-based products. 1.2 Two types of test methods are provided: fundamental and application methods. 1.2.1 Fundamental Test Methods-These test methods characterize the...
4.1 Test Methods E119 and E1529, and other standard fire resistance test methods specify that throughout exposures to fire and the hose stream, a constant superimposed axial load be applied to a load-bearing test specimen to simulate a maximum load condition. These test methods specify that...
5.1 Solid lubricant coatings are applied to surfaces that are exposed to heat and cold to such a degree that in many cases liquid lubricants are not practical. Adherence under these conditions is mandatory to preserve the bearing surfaces during sliding motion.
1.1 This test method covers a pin-type bearing test of metallic materials to determine bearing yield strength and bearing strength. Note 1: The presence of incidental lubricants on the bearing surfaces may significantly lower the value of bearing yield strength...
4.1 This practice is primarily intended for use by associations, third-party grading agencies, technical societies and other groups that develop national design standards and use recommendations for round timber piles. 4.2 This practice provides procedures for establishing compression parallel to...
1.1 This practice establishes a method for alternative shear wall systems to compare seismic equivalency parameters (SEP) derived from cyclic in-plane racking tests to performance targets derived from tests of light-frame shear walls constructed with wood structural panel (WSP) sheathing attached...
5.1 Understanding the mechanical properties of frozen soils is of primary importance to frozen ground engineering. Data from strain rate controlled compression tests are necessary for the design of most foundation elements embedded in, or bearing on frozen ground. They make it possible to...
This test method covers the procedures for the standard practice of performing magnetic particle examination of continuous grain flow crankshaft forgings intended for medium speed diesel engines. Crankshafts shall be divided into four zones of decreasing operational stress, each of which have been...
5.1 Before proceeding with these test methods, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test methods. If there...
1.1 This test method covers procedures for the determination of initial pH (i-pH) in new and in-service lubricants. Note 1: In new and used oils, the constituents that may be considered to have characteristics influencing the i-pH value include organic and inorganic acids, esters, phenolic...
Narrow Your Results