loading
ASTM C901-26 - Standard Guide for Design and Installation of Prefabricated Masonry Elements
June 1, 2026 - ASTM International

This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Structural design of panels shall be performed in accordance with the provisions of the applicable local building code and the...

ASTM D6594-26 - Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135?°C
June 1, 2026 - ASTM International

5.1 This test method is intended to simulate the corrosion process of non-ferrous metals in diesel lubricants. The corrosion process under investigation is that believed to be induced primarily by inappropriate lubricant chemistry rather than lubricant degradation or contamination. This test method...

ASTM D6110-26 - Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
July 1, 2026 - ASTM International

5.1 Before proceeding with this test method, refer to the material specification for the material being tested. Any test specimen preparation, conditioning, dimensions and testing parameters required by the materials specification shall take precedence over those required by this test method. Table...

ASTM C844-26 - Standard Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
May 1, 2026 - ASTM International

This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering...

ASTM E814-26 - Standard Test Method for Fire Tests of Penetration Firestop Systems
June 1, 2026 - ASTM International

1.1 This test method is applicable to firestop systems of various materials and construction. Firestop systems are intended for use in openings in fire-resistive walls and floors that are evaluated in accordance with Test Methods E119. 1.2 Tests conducted in conformance with this test method record...

ASTM D7119/D7119M-21(2026) - Standard Guide for Sampling Spray Polyurethane Foam and Coating in Roofing
May 1, 2026 - ASTM International

4.1 Adequate coating thickness (mil thickness) is necessary to protect polyurethane foam from the effects of ultraviolet degradation. This guide outlines general procedures for sampling and measuring the coating thickness by using slit or core samples. 4.2 Thickness of individual lifts of sprayed...

ASTM F432-19(2026) - Standard Specification for Roof and Rock Bolts and Accessories
May 1, 2026 - ASTM International

1.1 This specification covers the chemical, mechanical, and dimensional requirements for roof and rock bolts and accessories. Addressed in this specification are double-end threaded bars; fully grouted bolts and threaded bars; mechanical anchorage devices used for point anchorage applications; roof...

ASTM B700-26 - Standard Specification for Electrodeposited Coatings of Silver for Engineering Use
May 1, 2026 - ASTM International

1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be matt, bright, or semibright and are not less than 98?mass?% silver purity. 1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces,...

ASTM G225-26 - Standard Practice for Electrochemical Measurement of Corrosion Rate of Metals in Field Concrete Structures
May 15, 2026 - ASTM International

5.1 Because of its simplicity and accuracy, the polarization resistance technique has been widely used in the laboratory in numerous metal/electrolyte systems (2, 7-10). However, its application in real-size elements is not straightforward because of the need for referral to the actual polarized...

ASTM D4739-26 - Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
May 15, 2026 - ASTM International

1.1 This test method covers a procedure for the determination of basic constituents in petroleum products and new and used lubricants. This test method resolves these constituents into groups having weak-base and strong-base ionization properties, provided the dissociation constants of the more...

ASTM D8633-26 - Standard Test Methods for Evaluating the Cross-Grain Compression Strength and Stiffness of Wood and Wood-Based Products
April 1, 2026 - ASTM International

1.1 These test methods cover standardized procedures for evaluating the cross-grain compression strength and stiffness of wood and wood-based products. 1.2 Two types of test methods are provided: fundamental and application methods. 1.2.1 Fundamental Test Methods-These test methods characterize the...

ASTM D6513-26 - Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
April 1, 2026 - ASTM International

4.1 Test Methods E119 and E1529, and other standard fire resistance test methods specify that throughout exposures to fire and the hose stream, a constant superimposed axial load be applied to a load-bearing test specimen to simulate a maximum load condition. These test methods specify that...

ASTM D2511-26 - Standard Test Method for Thermal Shock Sensitivity of Solid Film Lubricants
March 1, 2026 - ASTM International

5.1 Solid lubricant coatings are applied to surfaces that are exposed to heat and cold to such a degree that in many cases liquid lubricants are not practical. Adherence under these conditions is mandatory to preserve the bearing surfaces during sliding motion.

ASTM E238-17a(2025) - Standard Test Method for Pin-Type Bearing Test of Metallic Materials
November 1, 2025 - ASTM International

1.1 This test method covers a pin-type bearing test of metallic materials to determine bearing yield strength and bearing strength. Note 1: The presence of incidental lubricants on the bearing surfaces may significantly lower the value of bearing yield strength...

ASTM D7381-07(2026) - Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material
March 1, 2026 - ASTM International

4.1 This practice is primarily intended for use by associations, third-party grading agencies, technical societies and other groups that develop national design standards and use recommendations for round timber piles. 4.2 This practice provides procedures for establishing compression parallel to...

ASTM D7989-26 - Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels
April 1, 2026 - ASTM International

1.1 This practice establishes a method for alternative shear wall systems to compare seismic equivalency parameters (SEP) derived from cyclic in-plane racking tests to performance targets derived from tests of light-frame shear walls constructed with wood structural panel (WSP) sheathing attached...

ASTM D7300-26 - Standard Test Method for Laboratory Determination of Strength Properties of Frozen Soil at a Constant Rate of Strain
March 1, 2026 - ASTM International

5.1 Understanding the mechanical properties of frozen soils is of primary importance to frozen ground engineering. Data from strain rate controlled compression tests are necessary for the design of most foundation elements embedded in, or bearing on frozen ground. They make it possible to...

ASTM A986/A986M-01(2026) - Standard Specification for Magnetic Particle Examination of Continuous Grain Flow Crankshaft Forgings
February 1, 2026 - ASTM International

This test method covers the procedures for the standard practice of performing magnetic particle examination of continuous grain flow crankshaft forgings intended for medium speed diesel engines. Crankshafts shall be divided into four zones of decreasing operational stress, each of which have been...

ASTM D256-26 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
April 1, 2026 - ASTM International

5.1 Before proceeding with these test methods, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test methods. If there...

ASTM D7946-26 - Standard Test Method for Initial pH (i-pH)-Value of Petroleum Products
March 1, 2026 - ASTM International

1.1 This test method covers procedures for the determination of initial pH (i-pH) in new and in-service lubricants. Note 1: In new and used oils, the constituents that may be considered to have characteristics influencing the i-pH value include organic and inorganic acids, esters, phenolic...

Advertisement