FOREWORD: Each year in the United States several thousand wells are drilled and completed - some productive of oil or gas and some dry - and during this drilling and completion most of these wells are cased, with the casing set in the bore hole surrounded by oil-well cement. This book has...
This specification covers either untextured or surface textured non-asbestos fiber-cement flat sheets intended for exterior applications such as claddings, facades, curtain walls, soffits, and so forth. This specification does not apply to asbestos-cement flat sheets, gypsum-based...
1.1 This test method, which is applicable only to portland cements and portland-limestone cements, covers the determination of the expansion of mortar bars made from a mixture of portland cement or portland-limestone cement and gypsum in such proportions that the mixture...
1.1 This specification covers asphalt suitable for undersealing portland-cement concrete and overlaid concrete pavements by pumping hot asphalt under the slabs. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each...
1.1 This specification covers various grades of anhydrous calcined gypsum known as gypsum Keene's cement, designed for use in the base and finish coats of gypsum plaster. Note 1: The setting time is accelerated by the addition of other materials. Note 2: Keene's cements are generally...
This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve sheet. Both the nozzle...
4.1 This test method provides a procedure for the determination of density of hydraulic cement samples using non-instrumental techniques. 4.2 Relative density is used to calculate the volume occupied by hydraulic cement in various mixtures containing hydraulic cement. This is...
5.1 This test method provides a means of determining the compressive strength of hydraulic cement and other mortars and results may be used to determine compliance with specifications. Further, this test method is referenced by numerous other specifications and test methods. Caution must be...
1.1 These test methods cover determination of the fineness of hydraulic cement, using the Blaine air-permeability apparatus, in terms of the specific surface expressed as total surface area in square centimeters per gram, or square meters per kilogram, of cement. Two test methods are...
1.1 This test method specifies procedures for the metallographic determination of apparent porosity in cemented carbides. Note 1: The term "apparent porosity" is construed to mean all microstructures observed on a properly prepared, unetched surface, including structures resulting from...
1.1 This test method describes a procedure for measuring abnormally large grains and the frequency of those grains in cemented tungsten carbides (hardmetals). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility...
This specification covers the standard requirements for the application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. It also sets forth tables for proportioning of various plaster mixes and plaster thickness. The materials used shall consist of the...
1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers are formed and...
1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under...
1.1 This specification covers standard sand for use in the testing of hydraulic cements. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and...
1.1 This specification covers expansive components used with hydraulic cements that when combined and mixed with water, form an expansive component system that, after setting, increases in volume to a greater degree than the cement paste. Note 1: Appendix X1 provides guidance for...
5.1 Thermal power curves are used to evaluate the isothermal hydration kinetics of the combined mixture of different materials during the early period after being mixed with water. These isothermal power curves, or hydration profiles, may provide indications relative to setting characteristics,...
5.1 This test method provides a means of determining the compressive strength of hydraulic cement and other mortars and results may be used to determine compliance with specifications. Further, this test method is referenced by numerous other specifications and test methods. Caution must be...
Narrow Your Results