5.1 The determination of the total volume?percent of saturates, olefins, and aromatics in petroleum fractions is important in characterizing the quality of petroleum fractions as gasoline blending components and as feeds to catalytic reforming processes. This information is also important in...
1.1 This test method covers determining the activity of equilibrium or laboratory-deactivat
5.1 This test method is a comparative method intended primarily to test materials for compliance with compositional specifications or for monitoring. It is assumed that all who use these procedures will be trained analysts capable of performing common laboratory procedures skillfully and safely. It...
1.1 This specification covers limestone supplied for use as a mineral supplement in animal feeds. Note 1: The calcium needed for animal nutrition is customarily supplied by limestone. Such limestone must be sufficiently fine to blend with mixed feeds and yet be free from excessive...
5.1 This test method can be used to determine total sulfur levels in process feeds and finished products that fall within the scope of this test method. 5.2 Low levels of sulfur in process feed stocks can poison expensive catalysts used in petroleum refining processes. This test...
5.1 In the design and operation of reverse osmosis and nanofiltration installations, it is important to predict the CaSO4, SrSO4, and BaSO4 scaling properties of the concentrate stream. Because of the increase in total dissolved solids and the increase in concentration of the scaling salts, the...
5.1 The apparent density is an important measure of a material characteristic of the powder that is useful to the powder producers and powder users in determining quality and lot to lot consistency. 5.2 This test method is applicable to free-flowing and non-free-flowing metal powders, lubricated...
5.1 CEDI devices can be used to produce deionized water from feeds of pretreated water. This test method permits the measurement of key performance capabilities of CEDI devices using a standard set of conditions. The data obtained can be analyzed to provide information on whether changes may...
5.1 The determination of the total volume?percent of saturates, olefins, and aromatics in petroleum fractions is important in characterizing the quality of petroleum fractions as gasoline blending components and as feeds to catalytic reforming processes. This information is also important in...
1.1 This specification2 establishes requirements for seamless red brass (Copper Alloy UNS No. C23000)3 pipe in nominal pipe sizes, both regular and extra-strong. In the annealed temper (O61), the pipe is suitable for use in plumbing, boiler feed lines, and for similar purposes. In the drawn...
5.1 This test method can be a useful diagnostic tool in measuring the impurities and detecting their sources in high purity water, boiler feed water and steam condensate of high pressure power plants, and in the process water of certain industries requiring high purity water. 5.2 The...
1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair. 1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of...
5.1 A large number of industrial processes involve transfer and feeding of bulk solids, and the ability of such materials to flow in a controlled manner during these operations is critical to product quality. 5.2 Direct shear cells are among the most important methods for measuring the flow...
This specification covers seamless copper pipe in all nominal standard pipe sizes, both regular and extra-strong, suitable for use in plumbing, boiler feed lines, and for similar purposes. The material shall conform to the specified chemical requirements. The pipe shall be produced from one...
This specification covers standard requirements for welded ferritic stainless steel feedforward heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. All finished straight tubing or straight tubing ready for U-bending shall...
1.1 This test method covers determining the activity of equilibrium or laboratory-deactivat
5.1 In many petroleum refining processes, low levels of sulfur in feed stocks may poison expensive catalysts. This test method can be used to monitor the amount of sulfur in such petroleum fractions. 5.2 This test method may also be used as a quality-control tool for sulfur determination in...
5.1 Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes...
5.1 The measurement of particulate matter is widely performed to characterize emissions from stationary sources in terms of emission concentrations and emission rates to the atmosphere for engineering and regulatory purposes. 5.2 This test method provides near real-time measurement results and is...
4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...
Narrow Your Results