loading
GANA GLAZING MANUAL - GANA GLAZING MANUAL
GANA
A description is not available for this item.
ASTM C1394-20(2026) - Standard Guide for In-Situ Structural Silicone Glazing Evaluation
April 1, 2026 - ASTM International

1.1 The existing condition of SSG installations should be periodically evaluated in-situ to detect if problems exist, and if so found, to address them before they become severe or pervasive. Evaluation of existing SSG installations is required by certain building codes and local ordinances. This...

ASTM F588-26 - Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies, Excluding Glazing Impact
April 1, 2026 - ASTM International

5.1 These test methods are intended to establish a measure of resistance for window assemblies subjected to attacks (other than impacting glazing materials) by unskilled or opportunistic burglars. Resistance to higher levels of force generated by skilled burglary attack requires methods such...

ASTM E3534-26 - Standard Test Method for Vacuum Insulating Glass Durability
July 1, 2026 - ASTM International

5.1 This test method is intended to provide a means for testing the durability of the sealing system and construction of VIG units. 5.2 This test does not determine the suitability of VIG units for structural glazing applications. 5.3 This test does not determine the suitability of VIG units...

ASTM C1954-26 - Standard Specification for Decorative Enamels on Flat Glass
July 1, 2026 - ASTM International

1.1 This specification covers the aesthetic quality requirements for decorative enamels applied to flat glass for use in building glazing. 1.2 This specification covers the requirements for flat glass, with either organic or ceramic enamels applied. 1.2.1 Glass may be annealed,...

ASTM C964-20(2025) - Standard Guide for Lock-Strip Gasket Glazing
October 1, 2025 - ASTM International

3.1 This guide provides information and guidelines for the design of lock-strip gasket glazing systems. For related standards, see Specifications C542, C716, and C963.

ASTM C1115-17(2026) - Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
April 1, 2026 - ASTM International

1.1 This specification describes products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used to seal or serve...

ASTM C864-05(2026) - Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers
April 1, 2026 - ASTM International

1.1 This specification covers preformed dense elastomeric compression gaskets and accessories for use in sealing and glazing applications. These materials are generally used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building...

ASTM C716-06(2025) - Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials
October 1, 2025 - ASTM International

1.1 This specification covers installation procedures for lock-strip gaskets that comply with Specification C542 and for infill glazing materials in lockstrip gasket glazing applications used in building walls which are not more than 15° from a vertical plane. The prime performance...

ASTM F1915-05(2025) - Standard Test Methods for Glazing for Detention Facilities
June 1, 2025 - ASTM International

4.1 The predictable and reliable performance of detention glazing used in detention and correctional facilities is a major concern. These test methods aid in assigning a level of physical security to glazing used in window and door assemblies based upon objective tests which can be...

ASTM C1956-25 - Standard Test Method for Laminated Glass Edges when in Contact with Sealants and Glazing Tapes
August 1, 2025 - ASTM International

1.1 This test method covers a laboratory screening procedure for determining the compatibility of laminated glass edges with elastomeric glazing sealants and glazing tapes after exposure to heat, humidity, and ultraviolet light. 1.2 This test method is applicable to all types of...

ASTM C1956-25e1 - Standard Test Method for Laminated Glass Edges when in Contact with Sealants and Glazing Tapes
August 1, 2025 - ASTM International

1.1 This test method covers a laboratory screening procedure for determining the compatibility of laminated glass edges with elastomeric glazing sealants and glazing tapes after exposure to heat, humidity, and ultraviolet light. 1.2 This test method is applicable to all types of...

ASTM E2395-21(2025) - Standard Specification for Voluntary Security Performance of Window and Door Assemblies with Glazing Impact
August 1, 2025 - ASTM International

1.1 This specification covers performance requirements and methods of test for the resistance to forced entry of window and door assemblies. This specification addresses the capability of window and door assemblies to frustrate and potentially delay or deter opportunistic entry by unskilled and...

ASTM F1642/F1642M-25 - Standard Test Method for Glazing and Glazing Systems Subject to Airblast Loadings
April 15, 2025 - ASTM International

1.1 This test method sets forth procedures for the evaluation of hazards of glazing or glazing systems against airblast loadings. The specifying authority shall provide the airblast loading parameters. Glazing systems shall be as defined in Specification F2912. 1.2 The data...

ASTM F2912-25 - Standard Specification for Glazing and Glazing Systems Subject to Airblast Loadings
April 15, 2025 - ASTM International

This specification covers exterior windows, glazing panels, glazed curtain walls, and other glazed protective systems used in buildings that may be subjected to intentional and accidental explosions. The specification is designed for all glazing, glazing systems, and...

ASTM C771-14(2025) - Standard Test Method for Weight Loss After Heat Aging of Preformed Tape Sealants
October 1, 2025 - ASTM International

1.1 This test method covers a laboratory procedure for determining the weight loss after heat aging of preformed tape sealants. Note 1: Test Method C681 describes a weight loss or volatility test for knife-grade glazing compounds. 1.2 The values stated in acceptable metric units are to be...

ASTM E2203-14(2025) - Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
October 1, 2025 - ASTM International

1.1 This specification describes products composed of dense thermoplastic elastomers that are fabricated into gaskets and accessories (such as compression seals, setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used...

ASTM C1369-25 - Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
October 1, 2025 - ASTM International

1.1 This specification describes the properties of cold, liquid-applied, single or multi-component, chemically curing, elastomeric sealants used as the secondary seal of sealed insulating glass units, hereinafter referred to as the "sealant" (see Fig. 1). These sealants are intended to be a...

ASTM F3006-25 - Standard Specification for Ball Drop Impact Resistance of Laminated Architectural Flat Glazing
May 1, 2025 - ASTM International

1.1 This specification covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications. 1.2 This specification is intended for use as an in-plant quality control test to evaluate the impact performance of laminated flat glass...

Advertisement