loading
HYDRAULICS - HYDRAULICS OF PIPELINES: PUMPS, VALVES, CAVITATION, TRANSLENTS
HI/HYDRAUL
A description is not available for this item.
SWRI SEALANTS - SEALANTS: THE PROFESSIONALS' GUIDE
SWRI
A description is not available for this item.
J1374_202009 - Hydraulic Cylinder Rod Seal Endurance Test Procedure
September 9, 2020 - SAE International

Applies to hydraulic seals used to seal the rods of hydraulic cylinders which are components of off-road self-propelled work machines defined in SAE J1116.

ASTM D8112-26 - Standard Guide for Sampling, In-Service Lubricating Oils and Hydraulic Fluids in Industrial Applications
May 1, 2026 - ASTM International

5.1 Analyzing in-service lubricating oil and hydraulic fluid samples is crucial for assessing the condition of both the fluid and the equipment. The results of the fluid analysis guide the planning of any necessary corrective maintenance activities. 5.2 The objective of this guide is to...

ASTM D7853-13(2026) - Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete
June 1, 2026 - ASTM International

5.1 Due to hydraulic pressure that may be present on some applications, engineers need to understand the capability of these products to resist this pressure. This test allows engineers to compare products and verify pullout strength. 5.2 Hydraulic pullout resistance is a function of...

ASTM D8152-26 - Standard Practice for Measuring Field Infiltration Rate and Calculating Field Hydraulic Conductivity Using the Modified Philip Dunne Infiltrometer Test
February 15, 2026 - ASTM International

5.1 This practice shall only be used on soils having infiltration rates ranging from 2.5 mm/h (field hydraulic conductivity of 6.9?×?10-7 m/s) to 15000 mm/h (field hydraulic conductivity of 4.0?×?10-3 m/s). 5.2 This practice is useful for field measurement of the infiltration rate and...

ASTM D8550-25 - Standard Test Method for Determination of Infiltration Rate and Calculating Field Hydraulic Conductivity of Field Soils by Sealed Single-Ring Infiltrometer and Multiple Pressure Head Procedure
July 1, 2025 - ASTM International

5.1 This test method shall only be used on soils having infiltration rates ranging from 2.5 mm/h (6.9?×?10-7 m/s) to 1200 mm/h (3.3?×?10-4 m/s). 5.2 This test method provides the means to quantify field hydraulic conductivity (Kf) based on multiple pressure heads, infiltration rate of water,...

ASTM D7919-26 - Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
June 1, 2026 - ASTM International

1.1 This guide pertains to removal and analysis techniques to extract debris captured by in-service lubricant and hydraulic filters and to analyze the debris removed. 1.2 This guide suggests techniques to remove, collect and analyze debris from filters in support of machinery health...

ASTM D5782-18(2026) - Standard Guide for Use of Direct Air-Rotary Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
March 1, 2026 - ASTM International

4.1 The application of direct air-rotary drilling to geoenvironmental exploration may involve sampling, coring, in situ or pore-fluid testing, installation of casing for subsequent drilling activities in unconsolidated or consolidated materials, and for installation of subsurface water-quality...

ASTM D1229-03(2024) - Standard Test Method for Rubber Property—Compression Set at Low Temperatures
November 1, 2024 - ASTM International

4.1 Rubber products, such as hydraulic seals on aircraft, submarine hatch gaskets, and hydraulic brake cups, may be exposed to varying temperature extremes. This test method provides a means of determining the extent to which recovery from compression at normal ambient...

NAVY 33-P-44 - PACKING, HYDRAULIC-SEAL, SYNTHETIC-RUBBER
NPFC
A description is not available for this item.
ASTM D8277-25 - Standard Test Method for Wet Filterability of Lubricants and Hydraulic Fluids by Mass Flow Technique
April 1, 2025 - ASTM International

1.1 This test method covers determination of the wet filterability of lubricants and hydraulic fluids based upon mass flow rate measurements through a 0.8?μm membrane after ageing of the fluid in the presence of water. The procedure applies to lubricants and hydraulic fluids that are...

DIN 4905 - Hydraulic solidifying seals for well construction - Requirements and testing
September 1, 2020 - DIN
A description is not available for this item.
ASTM D5783-18(2025) - Standard Guide for Use of Direct Rotary Drilling with Water-Based Drilling Fluid for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
July 1, 2025 - ASTM International

4.1 Direct-rotary drilling may be used in support of geoenvironmental exploration and for installation of subsurface water-quality monitoring devices in unconsolidated and consolidated materials. Direct-rotary drilling may be selected over other methods based on advantages over other methods. In...

AS4213B - FITTING, PLUG, BEAM SEAL, HYDRAULIC
August 14, 2018 - SAE International
A description is not available for this item.
ASTM D6546-23 - Standard Test Methods for and Suggested Limits for Determining Compatibility of Elastomer Seals for Industrial Hydraulic Fluid Applications
July 1, 2023 - ASTM International

1.1 These test methods cover the procedure for measuring physical properties of elastomer seals in the form of O-rings after exposure to industrial hydraulic fluids and thermal aging. The measured properties are then compared to the physical properties of elastomer seals that...

ASTM D5872/D5872M-18(2025) - Standard Guide for Use of Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water Quality Monitoring Devices
July 1, 2025 - ASTM International

4.1 Casing advancement may be used in support of geoenvironmental exploration and for installation of subsurface water-quality monitoring devices in both unconsolidated and consolidated sediment. Casing advancement systems and procedures used for geoenvironmental exploration and instrumentation...

AMS7361B - Rubber: Ethylene Propylene (EP) Phosphate Ester Resistant Low Temperature Tg -67 °F (-55 °C), 75 to 85 Type M Hardness for Seals in Hydraulic Systems
December 13, 2023 - SAE International

This specification covers an ethylene propylene rubber in the form of molded rings, molded compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications.

ASTM D5781/D5781M-18(2025) - Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water Quality Monitoring Devices
February 15, 2025 - ASTM International

4.1 Dual-wall reverse-circulation drilling can be used in support of geoenvironmental exploration and for installation of subsurface water quality monitoring devices in unconsolidated and consolidated sediment or bedrock. Dual-wall reverse-circulation drilling methods allows for the collection of...

JIS HYDRAULIC & PNEUMATIC - JIS Hydraulic and Pneumatic Equipments Handbook
January 1, 2019 - JSA
A description is not available for this item.
Advertisement