This specification covers a corrosion and heat-resistant nickel alloy in the form of metal injection molded (MIM) parts.
1.1 This classification system covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and application from solution. 1.2 The properties included in this classification system are those required to identify the...
5.1 Flexural properties as determined by this test method are especially useful for quality control and specification purposes. They include: 5.1.1 Flexural Stress (σf)-When a homogeneous elastic material is tested in flexure as a simple beam supported at two points and loaded at the midpoint, the...
1.1 This specification covers requirements and test methods for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or molded solid wall poly(vinyl chloride) (PVC) gasketed sanitary sewer fittings to be used with sanitary corrugated wall sewer pipe manufactured to Specifications F2763, F2764,...
1.1 This guide describes general guidelines for the chemical, physical, mechanical, biocompatibility, and preclinical assessments of implantable synthetic polymeric absorbable devices. This guide also describes evaluation methods that are potentially useful and should be considered when assessing...
1.1 This specification covers requirements for the PAEK materials used and the requirements and methods of test for the dimensions, workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from...
MPIF Standard 35 is issued to provide the design and materials engineer with the information necessary for specifying powder metal (PM) materials that have been developed by the PM parts manufacturing industry. This section of Standard 35 deals with products manufactured by Metal Injection...
1.1 This test method describes a procedure for determining the compatibility of adhesives with plastics based on whether the adhesive causes cracking of stressed samples. 1.2 Specimen configurations and test fixture designs are given. 1.3 This test method is suitable for products in the form...
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 50?mm to 1500 mm [2?in. to 60 in.]. 1.2 The requirements of this specification are intended to provide non-pressure...
The material defined by this specification is a thermoplastic injection molded compound based on polycarbonate. These are non UV-stable materials.
The material defined by this specification is a thermoplastic injection molded compound based on polycarbonate. These are non UV-stable materials.
The material defined by this specification is a thermoplastic injection molded compound based on polycarbonate. This is a non UV-stable material.
1.1 This test method provides procedures for an indication of the environmental stress crack resistance of plastic injection molded open head pails, covers, and components as a summation of the effects of container design, resin, manufacturing conditions, field performance, and other...
The material defined by this specification is a thermoplastic injection molded compound based on polycarbonate. This is a non UV-stable material.
1.1 This test method covers a recommended procedure for examining odor or flavor properties or both of rigid polymeric packaging closures and fillable materials. 1.2 This test method can be used for single materials or coextruded materials that are foam molded, injection...
The material defined by this specification is a 15% mineral filled thermoplastic injection molding compound based on thermoplastic polyolefin elastomer (TPO). For mold-in-color with added UV stabilization for exterior, use WSS-M4D873-B1, or use WSS-M4D873-B2 for painting,...
5.1 Injection Molding-In injection molding, the difference between the dimensions of a mold cavity and of the molded specimen may vary according to the design of the mold and operation of the molding process. Factors such as mold and melt temperature, fill...
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 50?mm to 1500 mm [2?in. to 60 in.]. 1.2 The requirements of this specification are intended to provide non-pressure...
Narrow Your Results