4.1 This practice is useful as one method of controlling some electroplating solutions. It serves to indicate the presence of contamination or some other adverse condition. 4.2 Ductility measurements are of particular value when electroplated parts are to be subjected to moderate stress such as...
This specification covers bare round copper-clad steel wire for electronic application. Four classes of copper-clad steel wire are covered as Class 30HS, 30A, 40HS, and 40A. The wire shall consist of a core of homogeneous open-hearth, electric-furnace, or basic-oxygen steel with a continuous outer...
1.1 This test method covers the determination of additive elements, wear metals, and contaminants in used and unused lubricating oils and base oils by inductively coupled plasma atomic emission spectrometry (ICP-AES). The specific elements are listed in Table 1. 1.2 This test method covers the...
1.1 This method covers the apparatus and procedures for measuring the dynamic angle of repose and related properties of powders and bulk solids. 1.2 The maximum particle size of the specimen must be no greater than 2 mm. Note 1: Typically, this device is used for testing powders in the range of 1...
4.1 This guide is intended to advise and assist analysts in the effective application of SEM/EDS to the analysis of geological materials. It is intended to be applicable to most modern SEM/EDS systems typically available in the forensic laboratory. The theoretical foundation of SEM/EDS is covered...
1.1 This test method covers the determination of metals and other elements in residual fuel and crude oil by microwave plasma atomic emission spectroscopy (MP-AES). The specific elements within the scope of this method are V, Ni, Ca, Na, Al, Si, Zn, P, and S for residual fuel oil and Fe, V, Ni, Ca,...
1.1 This test method covers the measurement of film thickness of dried films of paint, varnish, lacquer, and related products using micrometers. Procedures A and B utilize stationary micrometers and Procedures C and D, hand-held micrometers. Procedures A and C are not...
1.1 This test method describes the procedure for the determination of trace elements in light and middle distillate petroleum products using inductively coupled plasma mass spectrometry (ICP-MS). 1.2 This test method should be used by analysts experienced in the use of inductively coupled plasma...
1.1 This test method is used to determine the amount and particle size distribution curve of particles with diameter 106 micrometers or smaller resulting from the attrition of granular pesticides. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not...
This practice outlines the standard procedures for performing petrographic examination of hardened concrete samples. The samples examined may be taken from concrete constructions, that is, all sorts of objects, units, or structures that have been built of hydraulic cement concrete. They may also be...
1.1 These test methods cover two procedures for measuring the thickness of diffusion coatings. 1.2 Test Method A is the determination of the dimensional-change thickness, defined as the difference in the thickness of the part before and after coating. (The terms micrometer thickness and part...
5.1 These test methods shall be used where precise dimensions are necessary for the calculation of properties expressed in physical units. They are not intended to replace practical thickness measurements based on commercial portable tools, nor is it implied that thickness measurements made by the...
1.1 This test method covers the measurement of dry film thickness (DFT) of coating films by microscopic observation of a precision-cut, shallow-angle crater bored into the coating film. This crater reveals cross sectional layers appearing as rings, whose width is proportional to the depth of the...
3.1 This test method is intended for determination of an average thickness of a specimen of thin sheet or foil based on mass, density, and area. It is intended to be used where pointwise contact thickness measurements by conventional means (micrometer, optimeter) do not have sufficient...
This specification covers drawn and annealed or soft round bare copper wire for electrical purposes. The matterial shall be copper of such quality and purity that the finished product shall have the properties and characteristics prescribed. Tensile strength, elongation, and resistivity of the...
1.1 This test method describes the determination of metals and contaminants in insulating oils by inductively coupled plasma atomic emission spectrometry (ICP-AES). The specific elements are listed in Table 1. This test method is similar to Test Method D5185, but differs in methodology, which...
This specification covers the thread configuration and dimensions for finishes for plastic bottles with screw-type closures. The bottle overflow and body dimensional tolerances are detailed. The test apparatus for determining bottle capacity consists of a balance, pipet, graduated cylinder, beaker,...
5.1 A common result of cellular stress is an increase in DNA damage. DNA damage may be manifest in the form of base alterations, adduct formation, strand breaks, and cross linkages (19). Strand breaks may be introduced in many ways, directly by genotoxic compounds, through the induction of...
5.1 The volume of a complex shaped PM part cannot be measured accurately using micrometers or calipers. Since density is mass per unit volume, a precise method for measuring the volume is needed. Archimedes' principle may be used to calculate the volume of water displaced by an immersed...
1.1 This test method covers the measurement of thickness of flexible packaging materials using contact micrometers. 1.2 The Precision and Bias statement for this test method was developed using both handheld and bench top micrometers with foot sizes ranging from 4.8?mm to 15.9?mm...
Narrow Your Results