This specification covers a disposable glass Westergren tube used for measuring the erythrocyte sedimentation rate. Covered by this specification are Type I (standard Westergren tube used in conventional racks only) and Type II (self-zeroing tubes used with racks that have...
This specification covers disposable blood sedimentation tubes suitable for determining sedimentation rates and the volume of packed red blood cells. This specification covers a tube intended for one-time use only. The tubes shall be fabricated borosilicate glass, Type I, Class...
This specification covers reusable blood sedimentation tubes suitable for determining sedimentation rates and the volume of packed red blood cells. The tubes shall be fabricated from borosilicate glass, Type I, Class B, or sodalime glass, Type II. A resistance to centrifugal force...
This specification describes the physical requirements and corresponding test methods for disposable glass blood sample capillary tubes for use in microhematocrit procedures. Covered here are two different types of capillary tubes, namely, Type I (coated with heparin), and Type II...
This specification covers UNS N08925, N08354, and N08926 alloy seamless, cold-worked or hot-finished pipes and tubes for use in general corrosive service. The materials should be supplied in solution-treated condition, heat treated and quenched in water or rapidly cooled by other means. The...
This specification covers seamless tubes of nickel and nickel alloy for use in condenser and heat-exchanger service. This covers outside diameter and average wall, or outside diameter and minimum wall tube. Tube shall be furnished in the alloys and conditions defined by this...
This specification covers 28 grades of seamless and welded titanium alloy tubes for surface condensers, evaporators, and heat exchangers. Seamless tube shall be made from hollow billet by any cold reducing or cold drawing process that will yield a product meeting the requirements...
This specification covers the requirements for disposable glass culture tubes for use in culturing applications. Disposable glass culture tubes shall be made of type I (borosilicate) or type II (soda-lime) glass. Tube design shall be of one-piece construction. Other...
1.1 This specification covers the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications. 1.1.1 Tubes made from any of the following Copper UNS No. designations shall be supplied unless otherwise specified in the contract or...
This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping. The tube shall be manufactured by such hot- or cold-working process as to produce a homogeneous uniform...
1.1 This specification covers nickel-copper alloy UNS N04400 in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1. 1.1.1 Hot worked material is available. Properties and permissible tolerances are to be agreed upon between the manufacturer and...
This specification covers the technical characteristics of and test methods for insulating rods and foam-filled tubes made from fiberglass-reinforced plastic (FRP) that are intended for use in live line tools. This specification does not include insulating foam-filled tubes and rods...
5.1 Components of implanted medical devices can release ions, which may lead to adverse biological effects if released in sufficient quantities. Therefore, it may be necessary to characterize the ion release behavior over time to verify that a medical device or device components or both will not...
1.1 This specification covers the chemical, physical, mechanical, and metallurgical requirements for wrought nickel-titanium bar, plate, coil, and hollow containing nominally 54.5 to 57.0 weight percent nickel and used for the manufacture of medical devices and surgical implants. 1.2 Requirements...
5.1 Many petroleum products and some non-petroleum products are used as lubricants in the equipment, and the correct operation of the equipment depends upon the appropriate viscosity of the lubricant being used. Additionally, the viscosity of many petroleum fuels is important for the estimation of...
1.1 This specification covers drawn seamless tubes in straight lengths and coils for general purpose and pressure applications in alloys (Note 2), tempers, and thicknesses shown in Table 2 [Table 3]. Coiled tubes are generally available only as round tubes with a wall thickness...
1.1 This specification establishes the requirements for seamless round and rectangular including square copper alloy tube in straight lengths. Ten alloys are specified having the following nominal compositions: Copper Nominal Composition, % Alloy UNS No.2 Copper Zinc Lead Tin C22000 90.0 10...
1.1 This specification covers minimum-wall-thickness, seamless medium-carbon steel, boiler tubes and boiler flues, including safe ends (see Note 1), arch and stay tubes, and superheater tubes. Note 1: This type is not suitable for safe ending by forge welding. 1.2 The tubing...