loading
AMS7725A - TUNGSTEN ALLOY, SINTERED, HIGH DENSITY
January 1, 1976 - SAE International

This specification covers a tungsten alloy in the form of sintered shapes.

AMS7725C - Tungsten Alloy Shapes, Sintered, High Density
February 1, 2000 - SAE International

This specification covers two types of tungsten alloy in the form of sintered shapes.

AMS7725B - TUNGSTEN ALLOY SHAPES, SINTERED, HIGH DENSITY
April 1, 1992 - SAE International

This specification covers a tungsten alloy in the form of sintered shapes.

MIL-DTL-24252 - Cobalt-Chromium-Tungsten-Nickel Alloy (UNS R30605) and Cobalt-Chromium-Tungsten Alloy (UNS R30016) Bars and Forgings
November 8, 2006 - NPFC

This specification covers cobalt-chromium-tungsten-nickel alloy (UNS R30605) and cobalt-chromium-tungsten alloy (UNS R30016) wrought bars and forgings.

ASTM B482-25 - Standard Practice for Preparation of Tungsten and Tungsten Alloys for Electroplating
November 1, 2025 - ASTM International

2.1 The proper preparation and processing method choice for electroplating tungsten and tungsten alloys is often critical to the plating's performance. 2.2 This practice outlines recommended procedures to produce adherent finishes on tungsten and tungsten...

ASTM B445 - Standard Specification for Nickel-Chromium- Iron-Columbium- Molybdenum-Tungsten Alloy (UNS N06102) Seamless Pipe and Tube
January 1, 1987 - ASTM

This specification covers cold-worked nickel-chromium-iron-columbium-molybdenum-tungsten alloy (UNS N06102)* seamless pipe and tube in the conditions shown in Table 1. The values stated in inch-pound are to be regarded as the standard. The values given in parentheses are for...

ASTM B890-25 - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
September 1, 2025 - ASTM International

5.1 This test method allows the determination of the chemical composition of powdered and sintered tungsten-based hardmetals. This test method is not applicable to material which will not oxidize readily at high temperatures in air, such as tungsten/copper, tungsten/silver...

ASTM B890-20 - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
October 1, 2020 - ASTM International

5.1 This test method allows the determination of the chemical composition of powdered and sintered tungsten-based hardmetals. This test method is not applicable to material which will not oxidize readily at high temperatures in air, such as tungsten/copper, tungsten/silver...

ASTM B815-97 - Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Rod
April 10, 1997 - ASTM International

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rod for wear applications and general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Rods 3/16 to 3/4 in. (9.76 to 19.05 mm) exclusive in...

ASTM B814-95 - Standard Specification for :Nickel-Chromium-Iron-Molybdenum-Tungsten Alloy (UNS N06920) Plate, Sheet, and Strip
January 1, 1995 - ASTM International

1.1 This specification covers nickel-chromium-iron-molybdenum-tungsten alloy UNS N06920 in the form of rolled plate, sheet, and strip for general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip -Hot or cold rolled, annealed and...

ASTM B818-98a - Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Plate, Sheet and Strip
January 1, 1993 - ASTM International

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip -Hot or...

ASTM B755-00 - Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloys (UNS N06110) Plate, Sheet, and Strip
October 10, 2000 - ASTM International

1.1 This specification covers rolled nickel-chromium-molybdenum-tungsten alloys (UNS N06110) plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only.

ASTM B815-24 - Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy Bar or Rod
April 1, 2024 - ASTM International

1.1 This specification2 covers cobalt-chromium-nickel-molybdenum-tungsten alloy in the form of bar or rod. While the alloy is typically used for wear applications and general corrosion service, it is not limited to this usage. 1.2 UNS R31233 is the only alloy currently...

ASTM B814-06 - Standard Specification for Nickel-Chromium-Iron-Molybdenum-Tungsten Alloy (UNS N06920) Plate, Sheet, and Strip
December 1, 2006 - ASTM International

1.1 This specification covers nickel-chromium-iron-molybdenum-tungsten alloy UNS N06920 in the form of rolled plate, sheet, and strip for general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and StripHot or cold rolled, annealed and...

ASTM B818-03 - Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Plate, Sheet and Strip
June 10, 2003 - ASTM International

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip-Hot or...

ASTM B814-02 - Standard Specification for Nickel-Chromium-Iron-Molybdenum-Tungsten Alloy (UNS N06920) Plate, Sheet, and Strip
July 10, 2002 - ASTM International

1.1 This specification covers nickel-chromium-iron-molybdenum-tungsten alloy UNS N06920 in the form of rolled plate, sheet, and strip for general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip-Hot or cold rolled, annealed and...

ASTM B890-07(2012) - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
October 1, 2012 - ASTM International

5.1 This test method allows the determination of the chemical composition of powdered and sintered tungsten-based hardmetals. This test method is not applicable to material which will not oxidize readily at high temperatures in air, such as tungsten/copper or tungsten/silver...

ASTM B890-07 - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
March 15, 2007 - ASTM International

This test method allows the determination of the chemical composition of powdered and sintered tungsten-based hardmetals. This test method is not applicable to material which will not oxidize readily at high temperatures in air, such as tungsten/copper or tungsten/silver...

ASTM E696-07(2013) - Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire
May 1, 2013 - ASTM International

This specification covers the requirements for bare solid conductors made of tungsten and rhenium alloy thermoelements supplied in matched pairs. These thermoelements shall be suitable for use in either bead-insulated, bare-wire thermocouples, or in compacted metal-sheathed, ceramic...

Advertisement