loading
ASTM B793-16(2026) - Standard Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
April 1, 2026 - ASTM International

This specification covers the standard requirements for commercial zinc casting alloys in ingot form for use in the manufacture of sheet metal forming dies, sand cast or plaster cast forming dies, and plastic injection molds. Kirksite A alloy (UNS Z35543) is intended for use in the...

ASTM B833-20(2025) - Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
May 1, 2025 - ASTM International

1.1 This specification covers zinc and zinc alloy wire used to deposit zinc coatings by thermal spraying (metallizing) for the corrosion protection of steel and iron. Zinc and zinc alloy wire provided under this specification is intended for use in oxy-fuel...

ASTM B841-26 - Standard Specification for Electrodeposited Coatings of Zinc Nickel Alloy Deposits
July 1, 2026 - ASTM International

This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings,...

ASTM A1094/A1094M-26 - Standard Specification for Continuous Hot-Dip Galvanized Steel Bars for Concrete Reinforcement
April 1, 2026 - ASTM International

This specification covers requirements for steel reinforcing bars, with protective zinc or zinc-alloy coatings applied by the continuous hot-dip process. Continuous hot-dip galvanizing refers to the process of uninterrupted passage of long lengths of steel products through a molten...

ASTM A111-99a(2026) - Standard Specification for Zinc-Coated (Galvanized) "Iron" Telephone and Telegraph Line Wire
April 1, 2026 - ASTM International

This specification covers the standard requirements for iron wire with Class A, Class B, and Class C zinc coatings suitable for use in telephone, telegraph, and signal transmission lines. The zinc used for the coatings shall be of any grade while the base metal shall be made by...

ASTM A929/A929M-26 - Standard Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
June 1, 2026 - ASTM International

1.1 This specification covers steel sheet used in the manufacture of corrugated steel pipe for storm sewers, culverts, drains, and similar uses. The sheet is metallic coated by the hot-dip process. Material for this use is furnished in coils, flat in cut lengths, and corrugated in cut lengths. Many...

ASTM F3268-26 - Standard Guide for in vitro Degradation Testing of Absorbable Metals
February 1, 2026 - ASTM International

1.1 The purpose of this standard is to outline appropriate experimental approaches for conducting an initial evaluation of the in vitro degradation properties of a device or test sample fabricated from an absorbable metal or alloy. 1.2 The described experimental approaches are intended to...

ASTM F3744-26 - Standard Guide for Corrosion Fatigue Evaluation of Absorbable Metals
February 1, 2026 - ASTM International

5.1 Evaluation Strategy: 5.1.1 Corrosion fatigue evaluation of absorbable metals may be useful for screening and validation of alloys, processes, and coatings, and also for verification and validation of fully designed implants. Corrosion fatigue testing may also be useful for informing an...

ASTM D5185-26 - Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
March 1, 2026 - ASTM International

1.1 This test method covers the determination of additive elements, wear metals, and contaminants in used and unused lubricating oils and base oils by inductively coupled plasma atomic emission spectrometry (ICP-AES). The specific elements are listed in Table 1. 1.2 This test method covers...

JIS H 1111 - Methods for chemical analysis of zinc metal
March 20, 2014 - JSA
A description is not available for this item.
ASTM A740-21(2026) - Standard Specification for Hardware Cloth (Woven or Welded Galvanized Steel Wire Fabric)
April 1, 2026 - ASTM International

This specification covers woven or welded galvanized steel wire fabric commercially known as hardware cloth. It is customarily used for window and screen door guards, tree guards, industrial machine guards, sand screens, and grain bins. It serves as a protective screen against rodents and is used...

ASTM D4620-02(2025) - Standard Test Method for Evaluating the Effective Surface Area of Zinc Oxide in Rubber
November 15, 2025 - ASTM International

4.1 The surface area of zinc-oxide in rubber can significantly affect cure activation and vulcanizate properties. 4.2 The specific surface area of zinc-oxide is usually measured by nitrogen absorption which requires the use of equipment not normally found in rubber laboratories. This...

ASTM A875/A875M-25a - Standard Specification for Steel Sheet, Zinc-5?% Aluminum Alloy-Coated by the Hot-Dip Process
December 1, 2025 - ASTM International

This specification covers steel sheet, in coils and cut lengths, metallic-coated by the hot-dip process, with zinc-aluminum alloy coating. The coating is produced as two types: zinc-aluminum-mischmetal alloy (Type I) and zinc-aluminum-magnesium alloy (Type II), and in two...

ASTM A1079-25 - Standard Specification for Steel Sheet, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP), Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
December 1, 2025 - ASTM International

This specification covers steel sheet, complex phase grade, dual phase grade, and transformation induced plasticity grade, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hot-dip process in coils and cut lengths. The product is produced in various zinc...

ASTM D7803-25 - Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Powder Coating
September 1, 2025 - ASTM International

4.1 This practice describes the methods of preparation of hot-dip galvanized surfaces prior to the application of powder coating. The key to achieving proper adhesion between powder coatings and galvanized steel is surface preparation. The surface must be entirely free from visible metal...

ASTM A1046/A1046M-25a - Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process
December 1, 2025 - ASTM International

This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS types...

ASTM A875/A875M-25 - Standard Specification for Steel Sheet, Zinc-5?% Aluminum Alloy-Coated by the Hot-Dip Process
October 1, 2025 - ASTM International

This specification covers steel sheet, in coils and cut lengths, metallic-coated by the hot-dip process, with zinc-aluminum alloy coating. The coating is produced as two types: zinc-aluminum-mischmetal alloy (Type I) and zinc-aluminum-magnesium alloy (Type II), and in two...

ASTM A918-25 - Standard Specification for Steel Sheet, Zinc-Nickel Alloy Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface
October 1, 2025 - ASTM International

1.1 This specification covers zinc-nickel alloy coatings applied by the electrolytic process to hot-rolled and cold-rolled steel sheet. The coating has a smooth, spangle-free surface. The zinc-nickel-coated sheet covered in this specification is produced in a range of coating masses...

ASTM C1063-25a - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
November 1, 2025 - ASTM International

This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and...

ASTM A761/A761M-25 - Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches
October 1, 2025 - ASTM International

1.1 This specification covers corrugated steel structural plate, zinc-coated, used in the construction of pipe, pipe-arches, arches, underpasses, and special shapes for field assembly. Appropriate fasteners and accessory materials are also described. The pipe, arches, and other shapes are...

Advertisement