loading
ASTM A192/A192M-24 - Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
May 1, 2024 - ASTM International

This guide covers standard specifications for minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes...

ASTM A210/A210M-26 - Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes
April 1, 2026 - ASTM International

1.1 This specification covers minimum-wall-thickness, seamless medium-carbon steel, boiler tubes and boiler flues, including safe ends (see Note 1), arch and stay tubes, and superheater tubes. Note 1: This type is not suitable for safe ending by forge welding. 1.2...

Failure Investigation of Boiler Tubes: A Comprehensive Approach
January 1, 2018 - ASM

Failures or forced shutdowns in power plants are often due to boilers, and particularly failure of boiler tubes. This comprehensive resource deals with the subject of failure investigation of boiler tubes from basic fundamentals to practical applications. Coverage...

TAPPI TIP 0402-21 - Ultrasonic technician performance test for boiler tube thickness measurement
January 1, 2018 - TAPPI

This procedure has been developed by a TAPPI Task Group to offer a basis for evaluating the skills of technicians who measure the thickness of boiler tubes from the external surface using manual instruments. Use of this procedure is prudent when surveying the thickness of recovery...

ASTM A178/A178M-25 - Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater Tubes
September 1, 2025 - ASTM International

1.1 This specification2 covers minimum-wall-thickness, electric-resistance-welded tubes made of carbon steel and carbon-manganese steel intended for use as boiler tubes, boiler flues, superheater flues, and safe ends. 1.2 This specification covers Grades A, C, and D with...

MIL-E-17624 - EXPANDER, TUBE, ROLLER, BOILER TUBE
August 11, 1987 - NPFC

This specification covers boiler tube expanders of the self-feeding parallel rolling type for use in expanding carbon steel and alloy steel tubes in all types of boilers. Tube expanders shall be of the following types and classes, as specified (see 6.2): Type I -...

ASTM D8010-26 - Standard Test Method for Determination of Water Soluble Alkali in Coal
February 1, 2026 - ASTM International

5.1 Results obtained from the test method are used to serve a number of interests, including the indication of possible boiler tube fouling and possible furnace corrosion problems.

ASTM A213/A213M-25 - Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
September 1, 2025 - ASTM International

1.1 This specification2 covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2. 1.2 Grades containing the letter, H, in their designation, have requirements different from...

ASTM A192/A192M-17 - Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
November 1, 2017 - ASTM International

This guide covers standard specifications for minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes...

ASTM A423/A423M-19(2026) - Standard Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes
February 1, 2026 - ASTM International

This specification covers standards for minimum-wall-thickness, seamless, and electric-resistance welded low-alloy steel tubes to be used for pressure containing parts, that is economizers, and for other corrosion resistant applications. Steel tubes shall either be processed to hot or...

ASTM A1012-10(2025) - Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins
September 1, 2025 - ASTM International

1.1 This specification describes seamless and welded ferritic, austenitic and duplex alloy steel tubing on which the external or internal surface, or both, has been modified by a cold forming process to produce an integral enhanced surface for improved heat transfer. The tubes are used in...

ASTM A192/A192M - Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
November 1, 2017 - ASTM

This specification2 covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for highpressure service. The tubing sizes and thicknesses usually furnished to this specification are ½ in. to 7 in. [12.7 to 177.8 mm] outside diameter and 0.085 to 1.000 in. [2.2...

ASTM A450/A450M-25a - Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes
May 1, 2025 - ASTM International

This specification covers carbon and low alloy steel tubes. Steel samples shall be melt processed and shall either be ingot cast or strand cast. Heat and product analyses shall be performed on the steel materials. Steel specimens shall also undergo tensile tests and shall conform to required...

ASTM A213/A213M-24 - Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
May 1, 2024 - ASTM International

1.1 This specification2 covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2. 1.2 Grades containing the letter, H, in their designation, have requirements different from...

NACE 7H100 - Evaluation of Boiler Tube Deposit Mass Loading (Deposit Weight Density) Methodology
March 1, 2011 - NACE

Introduction Deposits or scale on the water/steam sides of boiler tubes result from in situ oxidation of the tube material, transport and precipitation of corrosion products from other locations within the system, and precipitation of mineral impurities from the boiler...

ASME STP-PT-066 - DESIGN GUIDELINES FOR CORROSION, EROSION AND STEAM OXIDATION OF BOILER TUBES IN PULVERIZED COAL-FIRED BOILERS
March 26, 2014 - ASME

FOREWORD This report provides a development of design rules for advanced power plant boilers that pertain to fireside corrosion, erosion and steam oxidation of boiler tubes. These boilers will operate at advanced steam conditions, include discussion of CO2 capture and...

ASTM A450/A450M-25 - Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes
March 1, 2025 - ASTM International

This specification covers carbon and low alloy steel tubes. Steel samples shall be melt processed and shall either be ingot cast or strand cast. Heat and product analyses shall be performed on the steel materials. Steel specimens shall also undergo tensile tests and shall conform to required...

TAPPI TIP 0402-13 - Guidelines for specification and inspection of electric resistance welded (ERW) and seamless boiler tube for critical and noncritical service
January 1, 2015 - TAPPI

This Technical Information Paper (TIP) covers guidelines to assure that boiler tubes for new construction and replacement, both in recovery and other boilers, are metallurgically sound and free from potentially harmful defects. Special emphasis is placed on obtaining tubing of...

ASTM A249/A249M-24a - Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
May 1, 2024 - ASTM International

1.1 This specification2 covers nominal-wall-thickness welded tubes and heavily cold worked welded tubes made from the austenitic steels listed in Table 1, with various grades intended for such use as boiler, superheater, heat exchanger, or condenser tubes. 1.2 Grades...

ASTM A249/A249M-24ae1 - Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
May 1, 2024 - ASTM International

1.1 This specification2 covers nominal-wall-thickness welded tubes and heavily cold worked welded tubes made from the austenitic steels listed in Table 1, with various grades intended for such use as boiler, superheater, heat exchanger, or condenser tubes. 1.2 Grades...

Advertisement