loading
ASTM B91-17(2025) - Standard Specification for Magnesium-Alloy Forgings
May 1, 2025 - ASTM International

This specification covers UNS M11311, M11610, M11800, or M16600 magnesium alloy forgings. The conformance of each material to the required chemical composition can be determined using any suitable method of chemical analysis. Samples for chemical analysis should be taken when the...

ASTM B94-18(2025) - Standard Specification for Magnesium-Alloy Die Castings
May 1, 2025 - ASTM International

This specification covers magnesium-alloy die castings. The magnesium alloys used for the manufacture of die castings shall conform to the chemical composition requirements of this specification. The producer or supplier is responsible for the performance of all...

ASTM B881-25a - Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
December 15, 2025 - ASTM International

1.1 This terminology covers the principal terms and definitions relating to aluminum- and magnesium-alloy products. It is published to encourage uniformity of terminology throughout Committee B07 product specifications. 1.2 Certain definitions and definitions of terms specific to a...

ASTM B881-25 - Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
November 1, 2025 - ASTM International

1.1 This terminology covers the principal terms and definitions relating to aluminum- and magnesium-alloy products. It is published to encourage uniformity of terminology throughout Committee B07 product specifications. 1.2 Certain definitions and definitions of terms specific to a...

ASTM B843-18(2025) - Standard Specification for Magnesium Alloy Anodes for Cathodic Protection
May 1, 2025 - ASTM International

This specification covers the standard requirements for magnesium alloy anodes in the form of cast and extruded shapes for use in cathodic protection. Materials shall adhere to specified chemical composition requirements, the samples for analysis of which shall be taken either from...

ASTM B199-17(2025) - Standard Specification for Magnesium-Alloy Permanent Mold Castings
May 1, 2025 - ASTM International

1.1 This specification covers magnesium alloy permanent mold casting alloys designated as shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only. 1.3 This standard does...

JIS H 4205 - Magnesium alloy forgings
August 20, 2020 - JSA

This Standard specifies requirements for magnesium alloy forgings (hereafter referred to as forgings). NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 3116 : 2007 Magnesium and magnesium...

ASTM B951-11(2025) - Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought
May 1, 2025 - ASTM International

1.1 This practice provides a system for designating unalloyed magnesium and magnesium-alloys that have been used commercially since 1952, and thus is intended to be the registration source for unalloyed magnesium and magnesium-alloys. A record of...

DS/EN 1753 - Magnesium and magnesium alloys – Magnesium alloy ingots and castings
October 1, 2019 - DS

This document defines the grades and the corresponding requirements for cast alloyed magnesium materials. This document specifies 2 groups of magnesium alloy grades by a classification based on the chemical composition. The first group deals with grades for...

ASTM B80-23 - Standard Specification for Magnesium-Alloy Sand Castings
April 1, 2023 - ASTM International

1.1 This specification covers magnesium-alloy sand castings designated as shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are provided for information only. 1.3 This standard does not purport to address all...

ASTM A1046/A1046M-25a - Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process
December 1, 2025 - ASTM International

This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS...

JIS H 4204 - Magnesium alloy extruded shapes
October 22, 2018 - JSA

This Standard specifies the magnesium alloy extruded profiles (hereafter referred to as profiles ) with a solid or hollow cross section, which are manufactured by extrusion. NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are...

ISO 26202 - Magnesium and magnesium alloys — Magnesium alloys for cast anodes
October 1, 2019 - ISO

This document specifies the grades and the corresponding requirements for magnesium alloy ingots for anodes and for magnesium alloy cast anodes.

ASTM A1046/A1046M-25 - Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process
October 1, 2025 - ASTM International

This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS...

ISO 3116 - Magnesium and magnesium alloys — Wrought magnesium and magnesium alloys
May 1, 2019 - ISO

This document specifies the chemical composition and mechanical properties of magnesium and magnesium alloys for wrought products in the form of bars and solid sections, tubes and hollow sections, forgings, and plate and sheet.

ASTM D1732-03(2023) - Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting
November 1, 2023 - ASTM International

1.1 These practices cover two classes of treatment for preparation of magnesium alloy surfaces for painting, as follows: Class I-Chemical Treatments. Class II-Anodic Treatments. In general, the latter treatments are the more protective of the two classes. Mechanical (abrasive)...

JIS H 4203 - Magnesium alloy bars and wires
October 22, 2018 - JSA

This Standard specifies the magnesium alloy bars (hereafter referred to as bars) and magnesium alloy wires (hereafter referred to as wires) with a circular, rectangular, square, regular hexagonal or regular octagonal or cross section, which are manufactured by extrusion...

MIL-DTL-32333 - ARMOR PLATE, MAGNESIUM ALLOY, AZ31B, WE43C, APPLIQUE
September 11, 2020 - NPFC

Scope. This specification covers wrought magnesium alloy armor plate in nominal thicknesses from 0.250 to 3.000 inch, inclusive (see 6.2). The fusion weldability of these wrought magnesium alloy armors has not been fully tested or analyzed over this entire nominal...

AMS2478F - Anodic Treatment of Magnesium Alloys Acid Type, Full Coat
December 13, 2023 - SAE International

This specification establishes the engineering requirements for producing an acid-type, anodic coating on magnesium alloys and the properties of the coating.

DIN EN 12438 - Magnesium and magnesium alloys - Magnesium alloys for cast anodes
November 1, 2017 - DIN

This European Standard specifies the grades and the corresponding requirements for magnesium alloys for cast anodes. This European Standard specifies 2 groups of cast magnesium alloy grades by a classification based on chemical composition. The first group deals with...

Advertisement