This specification covers UNS M11311, M11610, M11800, or M16600 magnesium alloy forgings. The conformance of each material to the required chemical composition can be determined using any suitable method of chemical analysis. Samples for chemical analysis should be taken when the...
This specification covers magnesium-alloy die castings. The magnesium alloys used for the manufacture of die castings shall conform to the chemical composition requirements of this specification. The producer or supplier is responsible for the performance of all...
1.1 This terminology covers the principal terms and definitions relating to aluminum- and magnesium-alloy products. It is published to encourage uniformity of terminology throughout Committee B07 product specifications. 1.2 Certain definitions and definitions of terms specific to a...
1.1 This terminology covers the principal terms and definitions relating to aluminum- and magnesium-alloy products. It is published to encourage uniformity of terminology throughout Committee B07 product specifications. 1.2 Certain definitions and definitions of terms specific to a...
This specification covers the standard requirements for magnesium alloy anodes in the form of cast and extruded shapes for use in cathodic protection. Materials shall adhere to specified chemical composition requirements, the samples for analysis of which shall be taken either from...
1.1 This specification covers magnesium alloy permanent mold casting alloys designated as shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only. 1.3 This standard does...
This Standard specifies requirements for magnesium alloy forgings (hereafter referred to as forgings). NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 3116 : 2007 Magnesium and magnesium...
1.1 This practice provides a system for designating unalloyed magnesium and magnesium-alloys that have been used commercially since 1952, and thus is intended to be the registration source for unalloyed magnesium and magnesium-alloys. A record of...
This document defines the grades and the corresponding requirements for cast alloyed magnesium materials. This document specifies 2 groups of magnesium alloy grades by a classification based on the chemical composition. The first group deals with grades for...
1.1 This specification covers magnesium-alloy sand castings designated as shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are provided for information only. 1.3 This standard does not purport to address all...
This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS...
This Standard specifies the magnesium alloy extruded profiles (hereafter referred to as profiles ) with a solid or hollow cross section, which are manufactured by extrusion. NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are...
This document specifies the grades and the corresponding requirements for magnesium alloy ingots for anodes and for magnesium alloy cast anodes.
This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS...
This document specifies the chemical composition and mechanical properties of magnesium and magnesium alloys for wrought products in the form of bars and solid sections, tubes and hollow sections, forgings, and plate and sheet.
1.1 These practices cover two classes of treatment for preparation of magnesium alloy surfaces for painting, as follows: Class I-Chemical Treatments. Class II-Anodic Treatments. In general, the latter treatments are the more protective of the two classes. Mechanical (abrasive)...
This Standard specifies the magnesium alloy bars (hereafter referred to as bars) and magnesium alloy wires (hereafter referred to as wires) with a circular, rectangular, square, regular hexagonal or regular octagonal or cross section, which are manufactured by extrusion...
Scope. This specification covers wrought magnesium alloy armor plate in nominal thicknesses from 0.250 to 3.000 inch, inclusive (see 6.2). The fusion weldability of these wrought magnesium alloy armors has not been fully tested or analyzed over this entire nominal...
This specification establishes the engineering requirements for producing an acid-type, anodic coating on magnesium alloys and the properties of the coating.
This European Standard specifies the grades and the corresponding requirements for magnesium alloys for cast anodes. This European Standard specifies 2 groups of cast magnesium alloy grades by a classification based on chemical composition. The first group deals with...
Narrow Your Results