loading
ISA MOTOR DRV - Motors and Drives - A Practical Technology Guide
January 1, 2003 - ISA

Introduction To study the subject of industrial process control effectively, you must first gain a general understanding of its basic principles. To present these control principles clearly and concisely, an intuitive approach to process control is used. First, however, some basic definitions and...

GMUTS L-12M-1 - Electric Motors - Vibrations MTL 0458
September 1, 2005 - GMNA
A description is not available for this item.
ASTM F3427-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Exoskeleton Test Methods
November 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

ASTM F1134-15(2025) - Standard Specification for Insulation Resistance Monitor for Shipboard Electrical Motors and Generators
June 15, 2025 - ASTM International

This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both. Monitors are intended for permanent installation in both existing or new panels and controller enclosures...

ASTM F1718-01(2024) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
November 15, 2024 - ASTM International

This specification covers the design and construction requirements of rotary positive displacement distillate fuel pumps intended for use in shipboard. Pumps covered by this specification are of Types II, III, IV, V, VIII, X, and XI and of sizes A-H. The pump shall be manufactured capable of...

DELPHI DX900176 - ELECTRIC MOTOR VIBRATION TEST (NO LOAD, FREE RUN)
DELPHI-I
A description is not available for this item.
PIP ELTFT03 - Electric Motor Mechanical Maintenance - Lubrication
March 1, 2021 - PIP

This Practice covers the basic requirements for the lubrication of antifriction and hydrodynamic bearings used in electric motors. These requirements apply to induction, synchronous, and DC motors. Excluded from this Practice: a. On site vibration analysis b. On site mechanical...

ASTM F998-12(2022) - Standard Specification for Centrifugal Pump, Shipboard Use
October 1, 2022 - ASTM International

This specification covers the requirements applicable to the design and construction of three classes of centrifugal pump (Class 1, Class 2, and Class 3) for shipboard application. When selecting material combinations, the conditions under which the various materials interact with each other shall...

GMW14482 - HVAC Blower, Stepper and DC Motor Noise and Vibration Evaluation Procedure
November 1, 2017 - GMW
A description is not available for this item.
UL 8801 - Photovoltaic (PV) Luminaire Systems
June 15, 2022 - ULSE

1.1 These requirements apply to low voltage luminaire systems whose electrical power is derived from photovoltaic modules. Systems include, at a minimum, a photovoltaic (PV) module, storage batteries, one or more co-located luminaires, and controls to manage the energy flow between these...

NOISE-VIBRATION PROBLEM - NOISE-VIBRATION PROBLEM-SOLUTION WORKBOOK
AIHA
A description is not available for this item.
DS/ISO 13373-9 - Condition monitoring and diagnostics of machines – Vibration condition monitoring -- Part 9: Diagnostic techniques for electric motors
October 17, 2017 - DS

ISO 13373-9 specifies procedures to be considered when carrying out vibration diagnostics of various types of electric motors. The four motor types covered by ISO 13373-9 are squirrel-cage induction, wound-rotor induction, salient-pole and DC motors. NOTE - The first two...

ASTM F1510-21 - Standard Specification for Rotary Positive Displacement Pumps, Ships Use
January 1, 2021 - ASTM International

This specification defines the requirements for rotary positive displacement pumps for shipboard use. This specification does not include pumps for hydraulic service or cargo unloading applications. Pumps under this specification include the following types and classes: Type II, Type III, Type IV,...

GMW15026 - Powertrain Mounts Without Integrated Hydraulic Damping
March 1, 2020 - GMW

Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose/Material Description. This specification covers the materials and performance requirements for...

J1537_202105 - Gasoline Low-Pressure Electric Fuel Pump Characterization
May 13, 2021 - SAE International

This SAE Recommended Practice defines the tests for three basic categories of pump characteristics. These are the basic functional performance tests, the pump limitation tests and the pump integrity tests. The basic functional tests included are three individual tests, with the first being for pump...

GMW15025 - Powertrain Mounts with Integrated Hydraulic Damping
March 1, 2020 - GMW

This specification covers the materials and performance requirements for powertrain mount components with hydraulic damping, Hydro Mount (HM) used for powertrain vibration isolation in motor vehicles. Note: Nothing in this standard supercedes applicable laws and regulations. Note: In...

ISO 13373-9 - Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 9: Diagnostic techniques for electric motors
October 1, 2017 - ISO

This document specifies procedures to be considered when carrying out vibration diagnostics of various types of electric motors. The four motor types covered by this document are squirrel-cage induction, wound-rotor induction, salient-pole and DC motors. NOTE The first...

DIN ISO 13373-9 - Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 9: Diagnostic techniques for electric motors (ISO 13373-9:2017)
March 1, 2018 - DIN

This document specifies procedures to be considered when carrying out vibration diagnostics of various types of electric motors. The four motor types covered by this document are squirrel-cage induction, wound-rotor induction, salient-pole and DC motors. NOTE The first...

Advertisement